Search results for query: *

Forum search Google search

  1. G

    Fj40 Boss Air Bag questions

    looks like the bottom mounts need to be flipped around to line up the bag.
  2. G

    77 fj40 passenger door glass?

    I'm looking for a passenger door glass for a 77 fj40 door. I'm not coming up with much. are they interchangeable between the pass and driver? I've been slowly collecting and working on this thing forever, and I would like to get it water tight and running at some point soon. I also need a glass...
  3. G

    Seat suggestions.

    what did it take to bolt in those seats?
  4. G

    Dim Instrument Cluster

    I saw some thread recently where he pulled out some baffles and it was much brighter.
  5. G

    1973 FJ40 SM465 Swap

    i've had luck using a torch to get out broken taps. it will heat the tap but not the shaft around it, and you can carefully blow it out of the hole.
  6. G

    SM465 adapter plate ?

    is your shaft an original one for that trans? my trans was 2wd and I bought a new 4x4 shaft to put in it. must have just been case hardened as it tapped easily.
  7. G

    FJ40 build shop - Chattanooga

    no idea, I do all my own work.
  8. G

    SM465 adapter plate ?

    I had the top off the trans so I could lock it in two gears at once, other than that the shaft was in the trans and I did it by hand.
  9. G

    SM465 adapter plate ?

    i just bought a tap and went for it. didn't have any issues once I drilled thru the hardness at the beginning.
  10. G

    SM465 adapter plate ?

    https://forum.ih8mud.com/threads/sm465-plate-adaptors.428058/ I used a masonry drill bit to get thru the hardened shaft end. then a standard bit did the work. tapped it to 9/16 fine thread.
  11. G

    Differential Pre Load

    got a machinist nearby? they can make you one. will this work...
  12. G

    1985 OEM Steel Pickup Rims

    they are on mine at the moment.
  13. G

    1973 FJ40 SM465 Swap

    I drilled my own shaft using a masonry bit, to get thru the initial shaft hardening, then a standard bit. tapped it 9/16 and was done. be awhile since I did it but wasn't too difficult.
  14. G

    clutch slave hose, sm465 swap.

    I know it will work, thats how my buddy had his setup. but he sold it and I don't remember how it was hooked together. guess I"ll get a custom hose made.
  15. G

    clutch slave hose, sm465 swap.

    what is everyone using for the clutch slave hose on a 465/v8 swap? I have the factory chevy hydro bellhousing and am planning on using the chevy slave and toyota master. Is there an easy solution or do I need to have a custom adapter hose made?
  16. G

    Electrical nightmare?

    that vw gas pedal is the worst thing. that alone might make it burst into flames!
  17. G

    Coalmont OHV Park update

    any news on this lately?
  18. G

    What angle did you mount your SBC at?

    if the carb flange is level, the engine is sitting about 5 degrees down at the rear. thats pretty much standard issue on rear wheel drive stuff.
  19. G

    For Sale Rear transfer case propeller mount

    still have this? I am in need of one.
  20. G

    gears?

    Don't need 3rd members, I have the tools and knowhow to do gearswaps, just wanted to make sure they were the same, and wether the flanges were the same spline. guess I'll figure it out soon enough.
Back
Top Bottom