Search results for query: *

Forum search Google search

  1. ripple

    starting problem...slow electricity

    I turn the key to start......wait a few seconds.....then, most of the time, it starts. After it runs and stops, sometimes 1, 3 or 4 or 30 tries and it starts. Maybe it's worse when it's humid. I just don't understand the time delay. I am replacing the starter again. Sometimes a jump start...
    • ripple
    • Thread
    • electricity start starter motor starting time delay
    • Replies: 5
    • Forum: 80-Series Tech
  2. ripple

    For Sale FJ40 Soft Top - Reduced Price - $450.00

    I want it too. I hope everyone bails and I get to buy it.
  3. ripple

    For Sale AZ : Landcruiser 80 Series Oak 2nd Row Carpet - Good Condition

  4. ripple

    SOLD Chattanooga, TN: FZJ80 a/c vents

    40 for the visors?
  5. ripple

    PO 758 Shift Solenoid 2 Resolved

    I replaced all my solenoids and then found a loose muddy connector to the tranny/solenoid. Not sure where the mud came from.
  6. ripple

    Cloth or Leather seats

    thumbs up for leather from lseat...replaced lx fronts...color was pretty much spot on but not as smooth as the original...fit was right on and it is a project to replace correctly...find what you like cause you don’t want to do it twice
  7. ripple

    Caster correction - bushings or plates for ~3 degrees?

    It could be that my pull to the right discussed in a previous thread, may be due to a caster correction issue. Never really was an issue till some taller skinnier tires. Anyway, alignment shows 0.3 deg caster and I need ~3. I have yet to discuss with Slee, but that is next since they are...
  8. ripple

    pulls to the right...still pulls to the right....still pulling to the right

    Thanks to all for joining me in tracking this down. I've had the truck for 10yrs. Cooper tires. It came with 4" OME and yellow bushings in the control arms. Update: I do notice a little less pull to the right when I'm on the left side a crowned road. I'm gonna get the front wheels off the...
  9. ripple

    pulls to the right...still pulls to the right....still pulling to the right

    It's not the crown in the road and that one is scary to test in the US. I did get an infrared thermometer to see if any discs were heating up after no braking and they are 90f and the hubs are 70f. No disc extra warmer than anything else. On flat and sandy ground no hands, brake, and the truck...
  10. ripple

    pulls to the right...still pulls to the right....still pulling to the right

    I did solve a pulling problem on this truck last summer by rebuilding the FR caliper. Got new tires and noticed a pull to the right. Maybe it was pulling some with the old tires, but I wasn't as concerned then. Replaced tie rod, front right caliper, adjusted bearing RF, swapped new tires...
  11. ripple

    Front brake caliper bolt holes

    thanks inkpot and tools r us, That's what I thought.
  12. ripple

    Front brake caliper bolt holes

    I'm about to pull one. But last time the caliper holes did not look like someone drilled one out and the bolt is tight in the hole. Same set up on each side if I recall.
  13. ripple

    Front brake caliper bolt holes

    Are the bolts/holes the some top and bottom? Mine are not. But the rebuilt calipers are. 97lx450 if that helps. thanks
  14. ripple

    For Sale Updated:sun ☀️ visors and steering wheel

    I need the lx450 visors please.
  15. ripple

    Wanted  74 fj40 passenger door glass

    Shipped to 80461? Or should I get one cut using the drivers side as a template?
  16. ripple

    SOLD FS: 4 FJC Steelies 17"x7.5" w/hubcaps $250 OBO

    Did you sell these yet? I can pick up.
  17. ripple

    Parting Out 96 FZJ80

    Clock spiral wire airbag connection in the steering wheel shipped to 80461? thanks
  18. ripple

    Parting Out 1997 lx450 N Fla

    looking for the clock spring spiral airbag connector in the steering wheel, thanks
  19. ripple

    Parting Out 95 Land Cruiser 96 LX450 Part Out Clean Title

    looking for the clock spring spiral airbag connector in the steering wheel
  20. ripple

    5.5in vacuum at 10,000 ft, I need more for the booster?

    thanks, I made a slight adjustment to timing to dial it in at 3, idle dropped to ~650 and it seems to have improved the booster, but no increase in vacuum at idle. Maybe the motor can recover vacuum quicker at lower rpm? We'll see in the morning when it's colder. Still not there but a little...
Back
Top Bottom