Trying to pool some knowledge as I'm sure I'm not the only one who's curious.
I'm running the Toyota H4 upgraded headlight harness in the 60'. I've been running H4's for the better part of four years and the bulbs are a noticeable upgrade from the sealed beams. Thus far I've run the following...
Figured I’d bounce this one off everyone to see if anyone experience a similar issue
I’m hearing very loud gearing sounds when I’m coasting in the truck. The higher the speed the higher the frequency.
It occurs whether the truck is in gear or in neutral, and engaging the clutch has no effect...
Looking for a clean, functioning turn signal harness that’s operable.
I’m chasing some a high beam issues and found that mine was repaired down the line with glue and should be replaced
PM me what you have and what you’re asking - some pictures of the contacts would be appreciated as well...
Gauging interest in a full set of Level 8 Tracker rims.
16x8.5 with a 4” backspace, I’ve run these on my 60 without any problems for years. I’m finishing a mild restoration on the truck so I’m looking to potentially move to a different rim.
Prior to being discontinued they retailed 120.00/Per...
SO after five years of asking questions and occasionally heckling people here its high time I put together a build thread for the truck to showcase the culmination of knowledge that helped get my 1987 Freeborn Red sixty series to where it is today
So for those of you who know me already...
Hi guys,
Just had one of my rear window hatch hinges snap - looking to source a set of functioning hinges ASAP
Does anyone have a pair? Please let me know
Thx,
James
Happy Friday everyone,
Looking for some solutions to my rear hatch issue.
The pin within the hinge seems to have sheared off so I’m on the hunt for a good fix - thinking these are my two options
#1. Drill it out, and find a matching bolt/roller pin at tractor supply (anyone know the diameter...
In today’s installment of “what does James manage to get himself into” we have my dash lights
Driving home from Boston I noticed both green turn signal arrows dimly lit - then as the night progressed I realized that my windshield washer fluid wouldn’t squirt - and simultaneously dimmed the...
So in another fine moment this morning I came out to the truck to find that someone carved the shift pattern out of my shift knob last night
That’s right folks, rather than unscrew the knob, they took a knife and popped out the glossy pattern.....can’t make this s*** up anymore.
They left the...
So I’m driving home tonight and I had my roof rack LED bar on for a few minutes as I went through some curvy roads and I started smelling Sulfer, pulled over and the battery was fuming.
Some back story, at the SAS this year my 8 year old auxiliary optima met the same fate, but I wasn’t using...
Looking for some collective input here in regards to my vortec. Having some work done and the codes P0174 & P0171 are turning out to be pretty much impossible to resolve
MAF: less than 9 months old (it’s clean)
02 sensors: relatively new, about a year
Fuel pressure: good pump is new(er)
What...
Its been three years without AC and i'm trying to cross the last hurdle....I've been cruising some threads and there doesn't seem to be a de-facto guide on AC when it comes to this swap. I know there is potentially a piece that needs to be removed from the amplifier...and i did as a much...
Looking for either two singles or a dual style Jerry can holder that I can use to secure two scepter style cans.
From what I understand AT makes some singles and metal tech does too, open to anything I can bolt down that has provisions to lock the cans within. Unforunately some cockroach used...
Looking for some pictures of those who wired up any lights on their roof rack, and where they ran the wires.
I have no desire to drill the roof, so I’m looking for a clean place to run the wiring loom to the battery, and on a 60 it looks like the options are slim
Let’s see some of your rigs...
Are there any pioneers out there that make ditch light brackets we can use on our 60s? Looking for some light options other than a roof rack or a bumper mount.
They make some for the 80 series that bolt on under the mirror, has anyone got creative with their rigs in a similar way? Always...
Hi guys,
After a particularly hard winter on my truck I’m trying to find some miscellaneous exhaust parts
Specifically the hanger seen in this diagram square #3
17430A and 17430B
The bracket 17430B (one of (2) that keeps A in place fell off and i can’t seem to find another one, and 17430A...
looking to buy a set of Trail Taylor stainless steel B-Pillar covers for a 60 series, if anyone has a set they’re looking to get rid of please shoot me a PM
Thanks,
James
Was going to throw some tough dog shocks I have stashed away on the rig today when I did the U-Joints
When i was looking over my front axle, I saw what seem to be welds on the bolts holding my stocks on, and the pattern is the same all the way around...
So, see for yourself. Are these welded...