Search results for query: *

Forum search Google search

  1. FF LC FREAK

    Taking my Bronco to the Arctic Ocean

    Hey all, I realize this is a Toyota forum, but I wanted to share an upcoming trip. I, along with a couple of buddies, am taking a trip to the Arctic Ocean this September in my 1994 Bronco. To make a long story VERY short, a buddy of mine is working on sponsorship from some big companies. I...
  2. FF LC FREAK

    car trailer?

    Hey, Anyone have a car trailer they would be willing to loan/rent out. I'm headed for Cruise Moab in 10 days, and the trailer I was planning on looks like it may fallen through. I'd probably need it April 28th to May 6ish. I'll know for sure in a few days, but I wanted to get this out there...
  3. FF LC FREAK

    Tube bender?

    Anyone have a tube bender that would assist me in bending some 1.25" DOM? I want to build some rear fender flares/sliders. Thanks!
  4. FF LC FREAK

    Builds  PLC build

    Hey everybody! Welcome to my 40 build! While this may not be as hardcore as some builds in this section, I'm putting it here because the 40 series section has been taken over by purists. This build is far from stock. And it seems our club forum has become defunct, which is where this build...
  5. FF LC FREAK

    Wanted  40 series high steer arms

    Hey all, I'm looking for some high steer arms. I have the late 40 series/ 60 series/ mini truck knuckle pattern. Preferably, I would like the arms with a 40 series taper so I don't have to get new tie rod ends or tie rods. Let me know what you got. Thanks! Kyle
  6. FF LC FREAK

    Wanted  4WD indicator switch for 71 fj40

    Looking for a 4WD indicator switch. It's the part that threads into the front output of the transfer case. It has 2 wires that come out of it. SOR says that 68-9/71 fits. Thanks! Kyle
  7. FF LC FREAK

    Wanted  "Pocket" knob for glove box

    Looking for a "pocket" knob for a 1971 40 series glove box. Mine died an inglorious death. It's just not the same without it. I believe they are the same E-4/78 (according to SOR). If someone has an extra laying around, let's make a deal! PM me with a price and condition. Thanks! Kyle
  8. FF LC FREAK

    Wanted  WTB: 2F alternator bracket

    As the title says, I need a 2F alternator bracket that puts the alternator on the upper right side (passenger side) of the engine. Thanks!
  9. FF LC FREAK

    Turbo / air filter question

    I have a turbo'ed 3B in a 1981 BJ42. When I added the turbo (and power steering at the same time), I didn't have room to plumb in the intake to the stock air filter location, so I used a cone style filter. I would really like to get back to the stock filter assembly if possible. I think the...
  10. FF LC FREAK

    24V Heater blower resistor

    Hi all, Does anyone know the specs on the heater blower resistor on a 24 volt rig? I broke my resistor, and it is beyond repair. They are NLA from Toyota. On my 12 volt fj40, the resistor is a 1 ohm 50 watt resistor. I'm guessing that would be incorrect on a 24 volt system, but I'm not...
  11. FF LC FREAK

    Is it bad to find metal in the oil pan?

    Kind of like this in my 3B oil pan? :lol: So, here's the somewhat condensed story. Last spring, I replaced all my cam bearings because of low oil pressure. Since I was into that far, I replaced the precups as well - they were all cracked, too. I had a factory Toyota MLS head...
  12. FF LC FREAK

    Mercedes 300d turbo - what else?

    Hey all, I am pulling a turbo off a Mercedes 300D this weekend. I've been searching through build threads, but I'm not really seeing what I'm after. Is there anything else I should pull besides the turbo? Oil lines? Fittings? What? My plan is to use a sawzall to cut the exhaust and...
  13. FF LC FREAK

    Head gasket question

    I have a question about head gaskets. Specifically, are all NEW Toyota head gaskets MLS? I just ordered this one from Cruiserparts.net (3B 13B-T Cylinder Head Gasket 8/80 and later [11115-58110] - $90.72 : CruiserParts.net, Toyota Landcruiser Parts), and they claim it is genuine Toyota. It is...
  14. FF LC FREAK

    3B motor mount and other questions

    Hey all, I yanked out the 3B today to replace the cam bearings. So, I have a couple of questions. 1. I have a busted motor mount. Are there any off the shelf replacements? I plan on doing the cam bearings tomorrow and then putting the motor back in. SOR lists an aftermarket motor...
  15. FF LC FREAK

    Wanted  81 BJ42 voltage regulator

    Hi all, I need to buy a 24 volt Canadian spec BJ42 voltage regulator. If you have one that you don't need, please PM me. Thanks! :cheers:
  16. FF LC FREAK

    Anyone have a SOR Voltage Regulator...

    ...and does it work? Story time. Grab a :beer:, sit back and enjoy... First, a little background. 1981 Canadian Spec BJ42. About a month ago, I blew my alternator and external voltage regulator. Got the alternator rebuilt, but I am having a hard time with the voltage regulator. I...
  17. FF LC FREAK

    Which bearing?

    I pulled off my oil pan today to fix some pin hole oil leaks. I found this: Its a 3B with unknown mileage. I just got done with a 900 mile trip and it did beautifully. Oil pressure was fine. Like I said, I only pulled the oil pan to fix the oil leaks. So, which bearing do you all think...
  18. FF LC FREAK

    BJ 42 brake warning light on?

    Hi all, Anyone know what else would cause a brake warning light to come on in an 81 BJ42? I have checked fluid level (good), hand brake lever(good), and vacuum pressure to booster (good - and a booster test pumping the brakes showed the booster was also good). This light just started coming...
  19. FF LC FREAK

    OEM soft door handle

    Hi all, I did a search, but I couldn't find any close up pics of the handles. If someone has a picture and some dimensions of the OEM soft door handles, I would sure appreciate it. Specifically, I need to know how long the latch part of the handle. Mine are broke off like this from the PO...
  20. FF LC FREAK

    cleaning female connectors

    cleaning female connectors - and EDIC issues Hey all, I was wondering if anyone has a good way to clean the female side of a 10 pin connector. Here's the story: I just recently picked up the EDIC relay for my 1981 BJ42 from the PO. He told me it was blown/no good, but I wanted it...
Back
Top Bottom