Hey, so I was looking into an idle issue and noticed just about every one of my wires on my MAF, TPS and IAC are in bad shape.
Does anybody know the correct terminal size / type that these housings use?
Any recommendation on mud vendors or suppliers to order the copper connectors and seals...
hi, could use a little help from someone familiar with the front pinion setup...
I am working on my 95 unlocked front carrier and was looking at toyota parts diagram. It clearly shows a washer between the stake nut and front pinion flange. But mine is absent. When I called toyota , they...
Been chasing a small coolant leak, its puddling on top of the thermostat, around and behind the bypass hose connection and we are loosing about 1/2 gal in a month. I originally changed the 3 o-rings for the small pipe that goes to the head. when that didn't work, i changed the bypass hose and...
Howdy-
Its time to refresh a weeping PS pump that is starting to whine. I dont have a press, nor the time to devote to rebuilding it myself...
RA has rebuilt units for less than 100$ that look pretty decent. There are 2 brands: Cardone and BBB Industries. I know nothing about either...
Ive got a weird charging problem, I thought was the alternator, but i took it to autozone- and it tested good. apparently I have a code for an open EGR, so they tried to sell me a new egr LMAO i dont think thats it) the battery checked out good too... So looking for some advice.
Started...
I'm about to address a couple rust patches on my hood and cowl, and will need to paint a couple areas. Does anyone know if the 045 single stage is an urethane or lacquer?
I'm looking into the PPG Omni acrylic urethane... im mostly worried the finish is not going to match and will be too...
I'm working on a 95 fzj80... Went to jump the pins to set my ignition timing and I have managed to mess up the wires inside my obd1 diagnostic port.
3 of the wires popped loose and I have no idea which ones they are. I have a brown, a white with blue stripe, and a green with pink stripe ( I...
so I stripped the threads on my fzj80 trans pan... I think it was overtightened, because the threads all came with the bolt 😕 has anyone had success tapping these to a slightly larger size?
I think its an m10x1.25 (not sure)
I was thinking of using a corolla drain plug which is m12x1.25...
So im paying stupid tax today. I bought some FIPG orange (00295-01281) only to find that after 2 days, it is still gummy and wet.
so I called the number on the tube for ThreeBond product support. turns out, the product was expired. There is an expiration date, but Toyota chooses not to...
So at 165k I'm doing hg and valves. A few of the exhaust valves had some pitting that I had to polish out.... I now have four valve clearnces that measure exactly 0.01" (0.252mm) .... literally on the low line for being within tolerance.( Which is 0.25-0.35 mm (0.0098-0.0138 in))
Will I...
Hi... so I'm attempting my first hg swap and valve job on my 1fz-fe, and I want to make sure I measure my valves correctly, but the cylinder head is off... and the FSM valve adjustment instructions only mention using the crank pulley for TDC then 360 turn for the second valve check...
Was pulling my wiring harness to remove the cylinder head, and seem to have caused a couple new issues.
1st is with the fuel injector wiring, I broke a few of them taking the injectors out, I see there's a repair harness, but I'm wondering if someone could share with me the proper way to...
Im looking up part numbers for flywheel bolts (to tc) and Toyota is telling me that of the 6 bolts, one should be green (90119-10789) and the others should be black (90119-10954). All of my bolts appear black, but after many years of oil dripping on them it's possible the green paint has...