Search results for query: *

Forum search Google search

  1. mexellent

    Tandem Off-Road 2G Sequoia Platinum Lift System Install Instructions

    Oh, this is an excellent question. Other than increased maintenance there is no downside to the air springs at all. Yes, adding pressure will make it more difficult to compress the suspension but that effort is WAY less than the coil bind you will experience with metal springs. Air...
  2. mexellent

    Tandem Off-road 2G Sequoia Rear Bumper Install Instructions

    It's a living document with instructions for installation of the bumper. I'll write the instructions here and if people run into problems then we can address them here once and other people can see how to resolve the problems as well.
  3. mexellent

    Tandem Off-Road 2G Sequoia Platinum Lift System Install Instructions

    You get about 2 inches which is what we recommend. You could get more but after that it's difficult to get alignment in spec. There will be a bit of positive camber but the important thing is to make sure the toe hits factory specs and you even out the camber on both sides. That would...
  4. mexellent

    Tandem Off-road 2G Sequoia Rear Bumper Install Instructions

    Step 6: Prepare to trim factory bumper Remove parking sensors and sensor harness Start to trim factory bumper. The first trim is the "Rough trim" Here is a template we are working on. Template explained The white line on the bumper is approximately where your first trim will be...
  5. mexellent

    Tandem Off-road 2G Sequoia Rear Bumper Install Instructions

    Step 5: Test Fit the bumper With the help of a friend, pick up the bumper and place it on the truck. Careful not to scratch the paint. PRO TIP: We like to use height adjustable tables. Super handy for putting bumpers on and when youre not using them to put on bumpers you can use them as...
  6. mexellent

    Tandem Off-road 2G Sequoia Rear Bumper Install Instructions

    Step 4: Prepare for test fit Remove the Trailer Plugs bolted to the frame and set these aside Make Clearance to slip the bumper on by trimming and folding in some tabs Hammer the trailer plug tab against the frame Cut the "skirts" hanging off the body on the left and right side of the...
  7. mexellent

    Tandem Off-road 2G Sequoia Rear Bumper Install Instructions

    Step 3: Remove the factory Rear Bumper Remove the factory mud flaps Disconnect the backup sensor harness from the vehicle Remove the factory rear bumper (save this for later) Remove the factory bumper support brackets located at the back of the vehicle Remove the bumper/mudflap supports...
  8. mexellent

    Tandem Off-road 2G Sequoia Rear Bumper Install Instructions

    Step 1: Assemble the Bumper Mount the Left and right Pin Plates to the bumper Mount the Swing Arm Strike Pads to the bumper Mount the Lightforce Rok40 flush mount lights to the bumper (optional) Step 2: Assemble the Swing Outs Install the Storage Doors The hinges are side specific and must...
  9. mexellent

    Tandem Off-road 2G Sequoia Rear Bumper Install Instructions
    Paint/Body: Installation Instructions

    This thread is to outline the installation of the Tandem Off-road rear bumper. The Sequoia has an integrated hitch into frame which makes it difficult to mount a rear bumper to the truck. There are two factory point on the frame with two bolt holes each that are used to mount the bumper...
  10. mexellent

    Shopping for a 2nd Gen Sequoia

    Ooooff.. Thats what I get for not reading teh whole thing. :doh:
  11. mexellent

    Tandem Off-Road 2G Sequoia Platinum Lift System Install Instructions

    Reserved for troubleshooting
  12. mexellent

    Tandem Off-Road 2G Sequoia Platinum Lift System Install Instructions

    Step 3A. Settle the rear suspension. -Now that the installation of the parts is complete, lower the vehicle back to the ground. The rear suspension will be at maximum compression as the airbags are deflated. -Now you can start the engine on the vehicle. Soon the air pump should begin inflating...
Back
Top Bottom