My FJ60 started to overheated when I got it due to a radiator that couldn't keep up. New radiator solved the problem. Also make sure the thermostat is working properly.
An thorough flush of the engine block with an effective agent will help greatly.
Years later once upon a time in back country...
Knocking pinging detonation all the same.
Fine tune your inline valve* so you have no stumble but also no pinging. It can be done.
Well explained here:
*If you use the one suggested you may want to try sucking on one end to get a feel for how much you restrict and use some flow restrictors...
Check your Ignition timing BTDC.
You must use Premium Fuel! 91 which has a higher knock (ping) resistance.
The best compromise solution is of course the inline valve. Finely tuned you get the best of both.
Yes, that's the one.
Alternately you can plug it also.
You will get better gas mileage and power.
Just don't forget to revert it should you need to do a smog test.
All the EGR does is recirculate a portion of the exhaust to lower combustion temperature.
NOX emissions do not form in significant...
...after the modulator, in the vac line that goes to the EGR.
You can test your EGR by sucking on that line and the idling engine should stall and stop.
(Careful thought should your EGR have a membrane leak you suck in some nasty s***!)
The FJ60 I had had the same problem.
There are two likely causes:
1. an EGR age related matter where the EGR for some reason opens to early and/or to fast.
Hence you disconnect the EGR (higher NOX) the problem seems to vanish.
Alternate Solution: reduce the vac flow to the EGR so it opens later...
Everything is fine on my side.
Fast connection, fast and stable PC.
Only with ih8mud.com I have this problem.
any other website, forum, etc., on the web loads fast and without any issues, except for those who have server side issues.
I always get this rotating three white small blocks in the...
Here we go again:
The connection was reset
The connection to the server was reset while the page was loading.
The site could be temporarily unavailable or too busy. Try again in a few moments.
If you are unable to load any pages, check your computer's network connection.
If your computer...
I'm on my desktop PC as always.
It happened after the old forum software was "upgraded" and/or "updated"
There was no issue at all before and it is only with ihmud.com
Just to confirm:
The preceding post took over a minute to post "Waiting for ih8mud...."
Often I get timeout errors "Page load error. The server forum.ih8mud.com... did not respond in time"
Clicking on any menu takes a long time to respond.
Do note this was no issue at all before this...
The Swiss have a most appropriate slang expression for such "improvements". It's a combination of two verbs.
"Verschlimmbessern"
Translated:
1. to make worse with so-called improvements
2. to "disimprove"
3. to improve for the worse
Literally:
"aggravating improvement" -> "aggraviments"
Why this stupid ih8mud forum software upgrade?
Why?
What's so much better on this clunk junk upgrade that is sooo slooow?
I have to wait and wait for pages to load or I get an timeout error.
I'm done!
I'm outta here!
I don't have the time and patience for such nonsense!
ih8stupid!
1986 FJ 60 Toyota Landcruiser for sale
360k miles, still runs!
Asking $ 3k or best offer
THE GOOD
·Rare 5 speed transmission
·Rust free straight chassis
·Rebuilt transfer case (Mudrak)
·New electric heated rear window (1 year)
·New front windshield (1 year)
·New Alternator (less than 2 years)...
https://forum.ih8mud.com/threads/1986-fj-60-landcruiser-360k-miles-still-runs-ok-2-575-or-best-offer.824377/#post-9454985
1986 FJ 60 Toyota Landcruiser for sale
360k miles, still runs ok!
Asking $ 2,575.- or best offer.
NO BUYER, IT WILL VERY SOON GO TO THE JUNKYARD!
(This crappy new forum...
Rear door does not work on a '93 4Runner.
Connecting motor directly to 12V source I can "open" and "close" the window. Other than that it won't work
When up and closed you can hear a click when pushing the button "up"
When pushing the button "down" nothing happens.
Anyone knows what the issue...