I am selling my set of 5 wheels and tires. Tires are 345/75/16 BFG KM2 and wheels are Interco birddogs.
check out my craigslist ad for details and pics: 37 tires & wheels - 345/75/16 - Toyota, Chevy, Nissan, GMC
Just trying to get feedback about Dobinson Radius arm bushings (no caster, just OEM replacements). My bushings are looking pretty shot, and the truck is shifting back and forth in its lane more noticeably lately.
Many on this board have suggested that OEM bushings hold up much better than the...
There is a rear hatch I would like to purchase from a seller in Tacoma and have delivered to SoCal (Santa Clarita specifically). Anybody running a route like that in the next month or two and could tie in this pick up/delivery?
Thank you
2004 Jayco Qwest Baja 10Z Tent Trailer - pop up -
Pics here: 2004 Jayco Qwest Baja 10Z Tent Trailer - pop up - RV
Always Garaged. Ready to go anywhere with high clearance and upgraded frame and suspension. Upgraded to LED bulbs. Loaded and Heavy Duty. Save on storage... it fits in a normal...
Hello! Selling the complete third members from my '97 land cruiser. Factory e-lockers. Rebuilt less than 4,000 miles ago with Nitro 4.88 gear kit (full kit, not just the r&p) by Ramjet (reputable diff shop). They function perfectly! I have a line on some 5.29s, that I'll replace them with...
SOLD!!!!
I'm selling a brand new set of OPOR (Outpost offroad - Metal Tech) Offset lower links. These are way beefier than stock, utilizing 1.75 x .250 wall DOM tubing, poly urethane bushings, 1" DOM sleeve with .25" wall support and a grease zerk fittings.
Details and PICS here: OPOR Offset...
Moved thread to AXLE classifieds. Please see there.
Hello! I'm considering selling the complete third members from my '97 land cruiser. Factory e-lockers. Rebuilt less than 4,000 miles ago with Nitro 4.88 gear kit (full kit, not just the r&p) by Ramjet (reputable diff shop). They function...
On the way back from Coyote Lake last weekend, I broke the passenger knuckle studs, forcing the knuckle and wheel off the truck (destroying the knuckle bearings (SPC 3 degree bearings) and leaving me stranded. I ended up being able to load the truck onto a trailer and get it home.
Now I am...
I just sheared my knuckle studs on the Red Lake/Coyote Lake Trail near Shaver Lake. Unfortunately when the studs sheared, it took out the upper knuckle bearing and knuckle seal and felt. The rig is undrivable. And I am a few miles up what is likely a green circle/blue square trail.
I'm...
Hey Guys,
I haven't been able to find any info on the topic for our 80 series rigs? I have bent my drag link running into rocks. I don't have the budget for high steer, so just wondering if anybody has ever produced or even considered an extended tie rod end for the drag link that would...
In regards to installing Marlin's crawler gears (transfer case), I notice that Marlin's instructions say, prior to disassembly, to engage low range so that we don't have to "re index the low range actuator upon assembly". What does "re index the low range actuator" look like?
The Factory...
Hey Guys,
I just wrapped up my engine build and am trying to hit the trail tomorrow morning. I also just finished up the install of the 3.1:1 crawler gears. I followed the directions and everything seemed to go together smoothly.
However, when I pull the transfer lever into Low Range, it...
I have removed all the lock rings (I think) and the shaft shifts back and forth along with the output bearing about 1/4", but won't fall out. How do I get this thing removed?
Thanks,
Hey guys,
Here is a pic of the my starter. Sorry it's oriented vertically. What is this terminal and where does it go? Does it go on the starter stud in the picture along with the large gauge cable from the battery?
thanks,
The engine, trans, and xfer case are removed from my FZJ80 and are almost ready to go back in (1FZ-FE Rebuild - Restoring my FZJ80 from an early demise)
What's the preferred method of re-installation? From what I've read, it seems like assembling the engine and trans outside the truck is the...
I began detailing the rebuild of the 1FZ-FE in my truck build thread (listed in my signature), but it soon began to dominate the thread, so I decided to create a dedicated thread.
My '97 Landcruiser died early and suddenly, with only 175k on the clock, when a misplaced bolt got into the timing...
Hello,
Will anybody from SoCal be attending FJ Summit? I have a lead on a rear hatch from my 97 from a Texan who will be at FJ Summit.
Thanks for your help,
Bryan