Search results for query: *

Forum search Google search

  1. D

    Color Change under the Hood?

    I’m looking for some creative solutions to a full color change including under the hood?
  2. D

    Interior/Exterior colors from factory

    I have 2 FJ80’s build one out of two. I’m looking for some opinions here 1991 Silver/Gray w/ Light blue interior Parts vehicle 1992 Red/Maroon w/ No interior What Exterior colors had the Blue interior? The 1992 will a full paint job, most likely bed liner. Has anyone just painted the engine...
  3. D

    LS swap engine sits to high

    I have poured over the numerous build of the past, read , looked at all the photos that still exist. My current situation is this, engine is sitting to high to clear the truck intake. In order for me to lower the engine, I have to move forward about 1.5” to clear the pan hard bar and A/C bracket...
  4. D

    Will this radiator fit my 1991 LC

    I have been looking for a new radiator for my 1991. I found this on eBay, Will it Fit?... http://m.ebay.com/itm/NEW-ALUMINUM-RADIATOR-FOR-TOYOTA-LAND-CRUISER-HDJ80-HZJ80-1HZ-1HD-4-2L-DIESEL-/271980026532?nav=SEARCH Thanks EDIT I looked through the pages of radiators I found a direct fit all...
  5. D

    For Sale  Complete locked axles front and rear

    I have a complete set of locked axles front and rear, switch, ecu, and harness ends I purchased these off a forum member and they are still on the pallet, and can be shipped via Fastenal3pl I'm looking to get $2500 Not a geat photo as they are in my storage container..,
  6. D

    For Sale  Complete LS Swap LQ9 Parts

    I have complete LS LQ 9 with most all parts to swap into a LandCruiser. I have never bailed on a project but some thing gets in my every time I pick up a tool! That said I have CONSIDERED selling it all. What we have a 2002 DBW LQ9 rebuilt top to bottom, all new parts on it, sensors, water...
  7. D

    Coolant temp sensor thread size?

    1991 Coolant temp sensor for the gauge on the dash board. Toyota part # 83420-20020 Can anyone confirm the thread size and pitch? So far I'm at 16mm can't find the pitch
  8. D

    ? About cutting 4l60e output shaft for Marks4wd kit

    Where am I supposed to cut the shaft? #4 gives me the measurement #5 says install adapter first. The adapter is 40mm, the difference between 170mm and 211mm If I measure off the adapter the output shaft is short. I had to change the output shaft from the 4wd version, not wanting to do it twice!!
  9. D

    4WD motor

    So I sucessfully put the transfercase back together, was a bit harder than expected! I'm down to the 4WD motor, the FSM says to install in a lock condition, I'm not sure where it was when I took it apart, but at this point I can move the shift fork by hand. Any help here would be great! Not...
  10. D

    Real time help! Transfer Case Re-assembly

    I am ready to re-assemble the transfer case. I did the Looka part time kit and front and rear output shaft seals, and bearings. (Thanks Beno!) ? What are you guys using to seal the case back up? FSM says Threebond, what I removed looked like red silicone? Also I need to torque the part time...
  11. D

    For Sale  1991 Engine and transmission

    I have the complete engine and transmission from my 1991. The motor is blown, looks a bad rod. New, alternator, water pump, belts Everything worked before it blew up 250k Trans still worked and shifted fine 250k Open to any offer on the parts
  12. D

    A/C for those that have LS engine

    In the process of getting additional parts for a LS swap. I have read/searched/followed every LS swap out there, on to my question. A/C compressor, it looks like many have a Sanden type with a low mount bracket, I have a LQ9 truck motor. Does it need to be relocated? Can anyone point in the...
  13. D

    16" or 17 " Wheels can't decide

    I found a set of 17" wheels local to me http://boston.craigslist.org/nos/pts/4906163166.html I am going to change over to rear disc brakes, and I understand I will need to dump the 15" wheels. I have done some search and see they will fit and could use a spacer to get BS the same. Is the...
  14. D

    Trasfer case help

    I am looking to purchase a part time transfer case. My searching tells me fj 60/65. I found one from a 1987. Are they all the same, coming from auto/manual trans? I intend to use this on a LS swap, using a automatic 2wd transmission. Can I get some direction on what to purchase, or look for...
  15. D

    Transfer Case Adapter??? LS based

    I am in the parts gathering process right now. I have the engine, had the output shaft changed to the 2wd version. On to the adapter. So I have looked at the adapters, and it looks like you need two? Then the the cost for 1991 version, coupled with possibly going to part 4wd, I'm thinking...
  16. D

    Springs? Rates,& Lift?

    Hey All, I recently got a mini vacation from work and Im planning some repairs and maybe some add ons? The repairs will be the front end rebuild bearings, seals, and birfields and some rust repair On to my question? I am wanting new springs, I have seen OME, TJM, ect. I am having trouble with...
  17. D

    Birfield choices

    Hey All, I have some clicking in the left front, lots of grease out and around the knuckle. I'm guessing all that's been done is greasing the front end. I have read up on old posts, and have the FSM. I'm going to tackle the job My question is this a good replacement part? The price looks...
Back
Top Bottom