My Injection Pump also makes a ticking noise that is alleviated only sometimes by pressing the hand primer.
Its more of a high pitched metallic rattle though. Like a rhythmic TTTTT TTTTT TTTTT TTTT TTTT lol. Sounds a bit like a rattling heat shield.
Depending on my coolant temp, it goes...
Hi Mdej3, We will definitely be talking soon. I will be moving to West palm beach within the next 2 or 3 months so I will be even closer to you.
I want this rust treated and fixed properly since I am using the truck as a daily driver LOL.
I'll shoot you an email.
Thanks!
So I have both a RHD and a LHD 80 series in my house. 1995 RHD & 1994 LHD
OEM # applicable here are
88501-60111 RHD
88501-60101 LHD
I ordered a spare RHD Denso evaporator on ebay from Australia to play it safe with any incompatibilities. Unfortunately, the evaporator arrived to the USA in...
Darne, would you have further info regarding the neoprene you used for your blend doors?
How compressible is it?
I ordered some "soft" poron open cell foam in 1/4 inch thickness. Looking at the non compressed sections of my original foam, this seems to be about the right thickness.
My...
I don't like to leave threads abandoned.
I tackled this job last week, and for a RHD HDJ81, its safe to say that the whole blower and recirculation door unit comes out without removing the dash and support bar as noted on the FSM. It was pretty easy. All my sealing foams are shot. No wonder I...
Hello all,
As the title says, I am looking for a quality and trustworthy shop that can (properly) fix and paint a rust spot on my 80.
It is the common area under the cargo windows at the C pillar level.
Cost or location are not really an issue, But I am located in S. Florida.
Any...
Hello,
The sealing foam on my recirculation doors are rotted and allowing fumes and dust to enter the cabin.
I have my evaporator box out for cleaning and was wondering if the whole dash needs to come out to also remove the blower/recirculation assembly (the whole box).
The manual states...
Just saw a little bulge at the rubber seal. I have many old Yotas. I can smell rust at this point. Luckily im not in the rust belt, but we get plenty of rain.
I thought of the same thing, but inspecting the area below the window seal briefly with a plastic trim remover, it seems that some areas are worn or missing paint down to the primer or e coat, and other areas are black all the way into the pinch weld. Its almost as if the paint has worn off over...
Hi everyone!
I have an absolute CREAMPUFF of a 1995 HDJ81. Single owner, non smoking and garaged for life. Full service records to boot, 150K (KMs) from Miyazaki japan. Non cold spec.
I thought I didn't have any major rust, being that the whole vehicle is so clean and original. That is until I...
Bringing this one back from the dead, but I cant find many posts about these tires in this size.
Would you say these ridge grapplers run small or big in this size? ie. Is it more like a 34 or a true 35 when mounted and inflated?
I'm thinking of these same tires for my 80.
Thanks!
Hi Ranma21, I have been trying to contact you thru PM.
Do you have new DEPO crystal headlights in stock? I need some LHD lights for my RHD 80 Series*** cruiser. Everyone is flashing me LOL.
Thanks!!
I have the same tick as OP. Intermittent at idle, constant only under light load up to 2K rpm, then disappears over 2K RPM. I have 140,000 K's.
I can hear it against curbs and walls mostly on right side. Engine has not blown up yet. I am running rotella T6 5W-40. I drive it daily and beat it...
Hello,
Might be a long shot.
Do you have the Transmission cooler, hardware, rubber hoses and the hard line junction that goes thru rad support?
Pic for reference. Thanks!!
Thanks!!
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.