Search results

  1. A

    How did I get water in my rear end

    HA HA Next time ill be more careful with my words. Turns out the driver side axle seal that wse barely leaking, agan not enough to drip, was bad. The tension spring that is suspose to be in the seal wasent I would emagine thats ware it came from. happy trails
  2. A

    GM tranny ID help & applications??

    Go to the technical links on this site there is a list of the casting # for the sm465. Also do search I found all kinds of info on the 465 here including how to mount it up to the 3sp transfer.
  3. A

    How did I get water in my rear end

    All brand new hose was used and the connection is tight I was extremly careful when running the hose not to pinch it etc. The left rear seal was leaking just berely, not even enough to drip. I to was thinking condensation but man thats allot for for no more time than was on that gear oil. Is...
  4. A

    How did I get water in my rear end

    I put new gear oil in the rear end last fall, went on 1 trip where I forded about 30 " of water. Other than that it basicley sat all winter. I decided to pull the cover and check on the welded rear end, WOW about 2 cups of water came out, I have extended the vent with 1/4" vacume tube so it...
  5. A

    Wanted Spring bushings fj40

    YA, I just thought if some one had a set sitten around and was tired of looking at them I'd put them back to work. :cheers:
  6. A

    Wanted Spring bushings fj40

    Just like it says i need a set of leaf spring bushings for a early fj40. prefably the factory rubber type, thay dont half to be in real great condition.
  7. A

    sbc electric fan temp sender

    What temperature range on the 1/2" pipe thread in block sender are you guys running for sbc with ford torus fan and stock 40 radiator. ex: on at 195 off at 190 This is what I'm running now and the fan pritty much stays on all the time,witch makes sence besause i have a 195 degree...
  8. A

    sbc to LC 3 speed conversion parts and starter

    For sale: 2 bell housings front and rear engine mounts both trani adaptor plates for putting a sbc in front of a 3 speed LC trani $ 100 OBO f motor toyota starter $ 30 OBO...
  9. A

    signaw power steer problems HELP!

    Update I finally got do some wheeling "some", Ended up braking the pinion but thats a different thing. After about 1 hr of fighting manual steering something came loose, the piston in the steering box. Now with 35-12.5's on pavement at idle 1 finger lock to lock. Thats the way it should be. So...
  10. A

    signaw power steer problems HELP!

    I called AGR yesterday, I doo have the lines correct. The port closest to the input shaft of the box is the pressure port. They couldent help with much else over the phone, other than make absouletly shoure the system is blead. And your hoses are in good shape so they dont suck air, eaven...
  11. A

    FJ40 bestop soft top - needs stitching repair.

    do you still have the top.
  12. A

    signaw power steer problems HELP!

    I agree :confused: The pump was on a circle track car, the box was on some gm car that i found in a old junk yard that was beaing dismantled for scrap steel. I had a hard time telling but it looked like a late 60's, hard telling how long it's been sitting. I'm going to finish the pump...
  13. A

    signaw power steer problems HELP!

    40 hasent been driven till yesterday, this it a new system, as new as it gets from a junk yard. I allso thought the lines were backwards. Tried to search yesterday if I had the pressure and return lines correct. I diddent find much but according to what I did find, thay are correct. Large port...
  14. A

    signaw power steer problems HELP!

    Thanks Steers eqally as hard on gravel and even drivng I'ts alittle better but not much, feals like manual. I'm cerous if it could be the seals internally in box. On the other hand the outer seals arn't leaking, is it then possable to assume the inner seals are ok?
  15. A

    signaw power steer problems HELP!

    I have a sbc with a 4 turn 4 bolt box (in front of the frame)and signaw pump, all parts are from a junk yard. The problem, It feals like manual steering. For good measure i filled the system, blead the system, draned it, filled and blead it agan. Symptoms I'm notising With the front tires...
  16. A

    Engine venting

    I have a old SB350 in my 40. I'n an attempt to make it as water resistant as possible I ran only 1 crank case vent from the PVC valve to the PVC valve vent on the carb. Is this enough crankcase ventalation or am I causing pressureization problems. THanks for your help
  17. A

    Wanted SM465 adaptor

    Still looking.........please help!!
  18. A

    disasemble birfield

    Thanks every one! I had a pipe that just slid over the c clip and was 3" longer than the longer inner. With a rag in the other end 4 pops and the long one was a apart one pop and the short one came apart. Total time spent about 3 mimutes. :cheers:
  19. A

    SBC parts and starter

    ttt
  20. A

    disasemble birfield

    I'm re greasing my knuckles and cant figure out how to disasemble the birfields to clean them and regrease. I read the article on the marlin tack and plan to do this. Sliding the C clip that's easy to git to does nothing. Eany sugestions or tricks would be great...
Top Bottom