Search results

  1. vfrer

    Todays wrenching

    That looks like a linked up 80 axle.... new toy?
  2. vfrer

    For Sale Wild WY! Large FJ40 parts lot. Early bibs, headlight buckets, gauge cluster, ashtray, door limiters, fender aprons, oil filter canister, bib lights.

    Aprons without badges and #19 buckets please... thanks! Interested in the clear bib lights too if hype passes. Eric
  3. vfrer

    SOLD Wild WY! Spare tire carrier body side hinge.

    Are you selling anything here? I'm interested in the aprons and will get in line for the hub caps if so. Regards Eric
  4. vfrer

    4 wheel disc brake help

    I think this is the nature of the monte carlo setup. The rear brakes are just too strong compared to the front so they will lock when the rear unloads. I read at one time that an alternate is some 2005-14 mustang rear calipers. I have them on the shelf but have not got around to installing...
  5. vfrer

    For Sale FJ40 PARTS - Misc.

    I'm interested in the one hub in the middle if still available. Eric
  6. vfrer

    Dash lights dim when Headlights are on?

    It does react but the max bright setting is just not as bright as it is with the headlights off.
  7. vfrer

    Dash lights dim when Headlights are on?

    Curious if anyone has figured out a way to have the brighter dash light mode with headlights on? I always have my lights on and it is very hard to see the climate control lights or the clock during the day.
  8. vfrer

    Front Clip Bolts?

    Definitely not stock. Stock bolt would be 91611-60820. It is a bolt with a flat washer.
  9. vfrer

    FJ40 Homemade GPS Digital Dash

    Pretty slick! Only first video played for me.
  10. vfrer

    How to Separate Axle Hub and Disc Rotor?

    Lug studs only need to be pushed out on 60 hubs. 40 hubs just need to be forced due to rusting.
  11. vfrer

    driveshaft u joint ??????

    I haven't installed it yet but I got this. The bolt pattern on the flange does not match a standard 40 pattern so had to get a round flange and drill holes. https://cruiserteq.com/long-travel-8-slip-joint-drive-shaft-kit-fits-early-current-land-cruisers-toyotas-uj35050/
  12. vfrer

    Metal Tech Tube Fender Kit and Safari Snorkel (?)

    It is going to depend on how the fenders were installed and how much room is left. You can put the tube fender at the stock height or all the way up to the hood if you want.
  13. vfrer

    Another FJ40 build from the ground up and it only took a week!

    Very cool and great detail... what program you using?
  14. vfrer

    Todays wrenching

    Mine whines bad, replaced pump gear and no change. I'm afraid to look at the engine gear and see something like that. What do you have to do to replace that gear in the engine?
  15. vfrer

    FJ40 Front Axle (Birfield) Maintenance Question

    to just get the birfs out you have to remove hubs and spindles at a minimum. you do not have to take the knuckles off but you may have to loosen the steering arms to pull them. if you just want to know if there is grease in the knuckle pull the square plug and stick a straw in and see if it...
  16. vfrer

    95 No Front Heat

    How did you burp the system? The only way I could get mine good was to park on a pretty steep incline and run it. Could tell when it was good when the heat started working again.
  17. vfrer

    This sheet metal baffle/cone thing in my rear axle housing….

    Mr T calls it an oil deflector, sounds like more than a hole.
  18. vfrer

    Another Noobie - First post and introduction

    Get in touch with Dan@4wheelauto.com for your Awl_TEQ rear sill. Had them in stock last week. Best price and quality around from what I can find. https://forum.ih8mud.com/threads/awl_teq-metal-parts-etc.972516/
  19. vfrer

    ||| Official YT For Sale/Trade/Wanted Thread |||

    Well you did motivate me to get the correct sill... Just ordered an early style for my '67 build from Dan at 4wheelauto. They are the vendor for Awl_TEQ. Had it in stock and it is on the way from Canada. Dan was very responsive and very nice. Said they have more parts in process too that are...
Top Bottom