Search results

  1. A

    Parting Out 1996 LC IN CHULA VISTA FOR PARTS

    If the rear wiper arm is still available Ill take it.
  2. A

    roof "rack" bolts

    definitely speed nuts, I think I will try and remove these and put in some riv-nuts.
  3. A

    roof "rack" bolts

    I don't have a roof rack on my 80 but I do have what I would call rails that have 2 T or U nuts per side, that you can slide forward and back. They are made out of aluminum (look like it) and have what look like speed nuts captured in them. My question is what bolts do I need? my experience...
  4. A

    CDL Stuck, won't disengage

  5. A

    CDL Stuck, won't disengage

    I just watched this video, and noticed he removed a plug from the connector and it had what looked like a jumper on the plug. I just removed my dash to put a mic on my radio and my connector definitely did not have this plug and of curse the jumper. Could this be why?
  6. A

    CDL Stuck, won't disengage

    yanking the fuse is a great idea BILT4ME. Cutrex are you thinking trans in nuetral or transfer case? Im still leaning toward the relay as there was definitely no audible click when shifting back into HI and no motor noise, vs, going into LO I could here the click.
  7. A

    CDL Stuck, won't disengage

    Well not a permanent solution but I was able to get the CDL unlocked by actuating the motor with a 9V battery. It wasnt like a binary fix, I ended up with the entire thing on jack stands and kept the battery connected while rotating the tires, it might have unlocked after applying power and...
  8. A

    CDL Stuck, won't disengage

    I haven't tried to hotwire it, you are talking about just applying voltage to pins 2 and 3 on the actuator right?
  9. A

    CDL Stuck, won't disengage

    There are quite a few threads on this already, even though the solution may be the same in end I couldn't seem to find anything with my scenario. I have a new to me 1995 FZJ80 with 213k. There is no CDL switch. I only have a CDL and NO diff locks. I was able to test out low range / 4wd over...
  10. A

    the use of scrap steel

    the bed rail material I used was pretty much impossible to drill through, and any weld joints were extremely brittle
  11. A

    Does cat cut down on exhaust fumes?

    I believe the sea foam comment was about testing for leaks NOT about the best product to clean the internals of the motor
  12. A

    Does cat cut down on exhaust fumes?

    I think I'll end up with a cat on one of other cars, it's tuned decent but still smells like exhaust, I'll update this thread
  13. A

    Does cat cut down on exhaust fumes?

    Did you ever install a cat? did it help? arndog
  14. A

    V8 conversion fuel line questions

    very surprised your carb has a 5/16 inlet on it, I don't think there is any harm in going 3/8s, most cars (muscle cars) of the 60s had 3/8s with a V8 regardless of output and 5/16 with a 6 cylinder with a holley im sure you can swap out the inlet fitting arndog
  15. A

    polytank fuel pickup size

    to be a little more accurate a 3/16 drill bit does not fit in the orifice of the existing barb arndog
  16. A

    polytank fuel pickup size

    I simply unscrewed the elbow from the top of the tank last night, looks like there was a 3/8 copper line soldered into the other end of the elbow I will be replacing the elbow with a 3/8 barb / 1/4 npt elbow, pressing in a 3/8s fuel line and should be in much better shape, the actual...
  17. A

    polytank fuel pickup size

    I have a poly tank and a 350 SBC, has anybody increased the size of the fuel pickup? 350s are 3/8s and from what I can tell the poly tank is a 1/4. Thanks, arndog
  18. A

    camcruisers tube fender build

    how about now :) can you upload them now? arndog
  19. A

    Fj60 leaf springs

    you still have these? If so you ever make it across the pass? arndog
  20. A

    [LI,NY] Confer Aux steel gas tank w/all accessories

    If your up for shipping to 98059 I'm in Arndog
Top Bottom