Search results

  1. Anvil

    Compressor not turning on

    Thank you Jsloden! I'm going to double check all of the switch jumping. I'll check the voltage on the blue/white wire this time. Thanks again!
  2. Anvil

    Compressor not turning on

    Yes sir, the compressor engages when 12v is applied. I tried ordering a new amplifier. Unfortunately, there is a national backorder on this part. Toyota doesn't know when the part will be in stock. :(
  3. Anvil

    Compressor not turning on

    I finally found time to troubleshoot again... I replaced the round relay, jumped the low pressure switch connector, jumped the thermistor connector, jumped the coolant temp sensor, and still no compressor engaging. Am I correct to assume there are only two components remaining that could be...
  4. Anvil

    Compressor not turning on

    Thanks jsloden and LandCruiserPhil! I truly apprciate your time!! Was your bad relay the round relay, or the rectangle relay that I haven't found yet?
  5. Anvil

    Compressor not turning on

    I finally found time to jump the thermistor plug... Nothing changed, so I guess the thermistor is good. Though I did buy a new one and will replace it soon, just because that's the way I am... Does anyone have a trick to removing the round relay above the evaporator (circled in red)? I wanted...
  6. Anvil

    Compressor not turning on

    Thank you jsloden! I honestly can't thank you guys enough. I truly appreciate everyones time. I'll give that a try tomorrow. I'm determined to figure this out. I failed to mention earlier, I had taken my rig to an ac shop... they were stumped and couldn't fix the problem. Thanks again!! :clap:
  7. Anvil

    Compressor not turning on

    Landcrshr, you were correct! #5 wire has power for a second or two while the starter is engaged. Now I'm back where I started... I've tried two amplifiers with no success.... hmmm...:hmm:
  8. Anvil

    Compressor not turning on

    Thank you landcrshr! I'll test that today.
  9. Anvil

    Compressor not turning on

    I can't thank you enough for your help! :clap: I'll give this a try tomorrow.
  10. Anvil

    Compressor not turning on

    Thank you sir! You've been a big help today. Here's one place I'm cofused (there are many!)... If I read the diagram ciorrectly, it shows the current comes out of the amplifier on #5/black wire. The FSM says there should be 10-14 volts coming in with engine running. #5 is the only wire that...
  11. Anvil

    Compressor not turning on

    Thanks Thanks jsloden! I apologize if I hijacked the thread. It wasn't my intent. I rebuilt my cooling system last year and want it back!! :) So I'm guessing do a continuity check from switch to amplifier connector? I have no CEL light. I welcome ideas/advice! you guys feel free to chime in...
  12. Anvil

    Compressor not turning on

    Can someone please tell me where the switch circled below is located? I used the FSM and volt meter to check the plug going to the amplifier. All was good except this wire. It should be supply 10-14 volts. It has nothing. Thanks!
  13. Anvil

    Compressor not turning on

    Thank you! I currently have the glove out and have easy access! Thanks again!!
  14. Anvil

    Compressor not turning on

    Thank you! I appreciate your time! I'll give this a try this weekend. Cheers!
  15. Anvil

    Compressor not turning on

    THANK YOU!!! I opened the amplifier... the circuit board looked good. I purchased another amplifier from Ebay and installed it. This did not help. So I'm questioning if the amplifier is bad.
  16. Anvil

    Compressor not turning on

    I have the same symtoms you had.... I have power going to the ac amplifier but none coming out. Where is this thermistor? How do you test it? Any help would be much appreciated! Thanks!
  17. Anvil

    AC amplifier test?

    Bump... Summer is coming and I'd like the get my A/c repaired! The a/c shop thinks the amplifier is the culprit. I replaced all a/c parts last year. Everything worked great... then the compressor suddenly would not engage. I can bypass and the compressor engages fine. My question is... How do...
  18. Anvil

    BSLCA BS... ie.. local chat..

    Any of you guys coming to the Lone Star Round up this weekend? If so, I'd like to place an order before you leave Lafayette. I miss my cajun food! :)
  19. Anvil

    Fender Flares - FJ80 92-97 from PocketFenderFlares.com

    No sir, as of this morning, the message I sent in August has not been read. Did you go with Kutsnakes? I'll be painting my rig this winter and need a set soon.
  20. Anvil

    Wanted  Wanted: 1997 1Fz-Fe engine

    Looking for a 1997 1FZ-Fe engine to rebuild for my 97. I'm not in a big hurry, but wanted to start looking. Please let me know what you have. Thanks!
Top Bottom