Search results

  1. AdventureRider

    For what is this sensor on intake manifolt?

    Hi, i ignored it 😂 as i got told... Asia climate doesnt need it!
  2. AdventureRider

    For what is this sensor on intake manifolt?

    Even with 35bar compression, new piston, sleeves, rings and valves... Still it would take a couple of turns more.
  3. AdventureRider

    For what is this sensor on intake manifolt?

    Thanks a lot for that answer. Ok so first i just ignore that sensor. Right? Second, on ly old 1HZ engine i always used the glow plugs. I had always starting issues if i didnt use them. It would crank over longer instead of just firing up. Will see on that 1HDT engine. Thanks again. More...
  4. AdventureRider

    For what is this sensor on intake manifolt?

    Hi, i just replaced my 1HZ engine with 1HDT engine. For what is this sensor on the intake manifolt next to oil dipstick. Is it a sensor? Where to connect to? one more question, can i use the two pol sensor left next to the oil filter as a coolant sensor for the dash board? i used to have on...
  5. AdventureRider

    1HDT water outlet with temp sensor port

    I have a question. can i just use the 2 sensor on the right and plug my two cables to? I have a 1HZ water outlet in spare with the temp sensor hole but it doesnt have the coolant hose underneath like the 1HDT. and the 1HDT didnt come with the coolant sensor hole/thread.
  6. AdventureRider

    1HDT on 1HZ manual gear box

    1st gear was always a kinda useless as long as you dont need L4. hahaha
  7. AdventureRider

    remove 1hz engine

    Thank you mudgudgeon, We exactly did it like this. Worked great!
  8. AdventureRider

    Engine Removal

    finally i found old tread. Thanks for that as i opened a new one. So basically there is no way around not dropping the transmission on a 1HZ engine as there is 1 bolt (1bolt only!!!) which can not be taken out without dropping the transmission, right? Wouldnt it be smart drilling out that thread...
  9. AdventureRider

    remove 1hz engine

    Hi, hope i am right here. i couldnt find anything in the search. I am removing my 1HZ engine to replace with 1HDT engine. I came to an issue removing it from transmission. Is there any way pros remove the engine without dropping the transmission? There is that one bolt up in the corner on the...
  10. AdventureRider

    1HDT on 1HZ manual gear box

    Ok, so does it change the driving behavior radically? Should i drop using 1st gear now? Any weak points do to different spline size? Is it plug and play or do i need to modify anything like different bearing obetween clutch/box and engine? I am living here in Cambodia. Except the workshop...
  11. AdventureRider

    What have you done to your Land Cruiser this week?

    First i did that... Result negative... No crack...
  12. AdventureRider

    1HDT on 1HZ manual gear box

    Hi, i am new here in the forum and i hope i am in the right section. Otherwise i would appreciate help to move thread. My question, after purchasing a 2nd hand engine 1HDT here in Cambodia i am planning to install it on my 1HZ manual gear box. Someone oversea told me to becareful as the 1HZ...
  13. AdventureRider

    1HZ COMPRESSION NUMBERS AND SIGNS OF A WEAK ENGINE

    1HZ engine is 37bar max and toast below 27b. 1HDT engine 35bar and toast at 25bar. difference of 10% in between cylinders is adequate. i just bought a 2nd hand 1HDT engine and can turn over the engine with a normal short ratchet on the pulley...feels way lower compression than my overhauled 1HZ...
  14. AdventureRider

    rear axle off center

    Hi, i am new to this forum and hope i do not ask a question where the answer is already known. I own a Landcruiser Year 92, manual, 4,2l diesel. I have been fixing this car here in Cambodia many many times as it had endless problems. I am now on a point where i am quite happy with the car and...
Top Bottom