Just pulled from the truck.
Complete interior wiring harness. The harness came from an Iowa truck so it is not sunbaked. All the connectors appear to be in very good condition. The harness is uncut.
I have the main harness from behind the dash.
I also have the left and right rear body harness...
This for a set of rear coil springs and rear long travel shocks.
The rear springs are : Dobinson's C97-147VT Long Travel, maximum flex variable rate tapered coils from Dobinsons, 2" Medium Load Use with Dobinsons long travel shocks for maximum flex
I purchased these and put them on. They...
The truck has a leaking head gasket. The body even though it looks nice is very rusty.
Bumpers front and rear have a deal pending.
Some of the cladding is available. Some of it needs repairs.
Interior has been stripped. No good visors. Oak interior. Lots of little parts ready to ship.
The...
Bought off another member , c2dfj45
Springs had less than 200 miles on them. I installed them last night and they are too tall for the weight of my stripped down 80. I am gonna go with a 2" lift spring instead. So I will be pulling them when my 2" springs arrive from Dobinson's.
There are...
Parting out two FZJ-80's
Champagne Colored 1994 with aftermarket brown leather interior. No lockers. Has been sitting for a long time. The motor has a rod knock. Low mileage truck. Around 150-160k on when the motor went.
1993 Grey with factory lockers. The front has a broken ring gear and the...
1997 Wells Cargo Trailer
Gooseneck Hitch
48' in length 8' wide 8' Height
2 7200lb axle
Load range G tires
28' living quarters
20' garage
Rear roll up door- does not have a ramp door 78' wide by 87" tall
76" between wheelwells.
Fullsize shower, hot water heater, toilet, fridge, stove top with...
Just picked up some spare parts from a 1992 FJ80 Dark Grey in color.
I have all four doors-if you need anything off these shoot me an offer- metal is not so great - small amount of rust- mirrors are there but don't appear super tight- switches are there-interior cloth panels are rough- all...
I picked truck up last spring with the intent of doing something with it. Since then things have changed. Truck runs and drives but has a rod knock. It drove itself on the trailer, off the trailer, and around the yard to a parking spot. Since then I haven't fired it up. It has no battery. It was...
Fit inside the rear coils. They were installed in my 80 when I got but I did not need them so I removed. I don't know much about them other than they where working when removed. Have been sitting on a shelf since. They are red in color.
Thinking $75 plus shipping but if thats out of line make...
1985 4runner Toyota Factory Service Manual
Maybe used once. Ordered it when I was redoing the motor in the 4runner. Of course it showed up after I was finished. Very nice condition. Paid $108 plus shipping
Will take $100
https://secure48.mysecureorder.net/offroadonly/catalog/product_info.php?cPath=21_42&products_id=113&osCsid=f520d4718cd1503a2f9bae73c274ee75
Won this at a local event. Don't need.
$75 OBO
1992 Lexus 1UZ-FE Motor 4.0 liter DOHC 32valve all aluminum V-8
1992 Lexus A340LE Transmission
Currently this motor is running in a Twisted Customs tube chassis. Got it running a little over a year ago. Motor at this point is running very well. It is already wired and would be very easy to...
Used have about six runs on them. 1 has some plugs in it. The other 4 are good. They have rock rash and some wear. But they are Red Label Krawlers.
They are located in Minnesota.
$1000 OBO
Need a fuse panel cover for a 1994 FZJ-80 with grey interior. Its the panel to the left and down of the steering wheel. Mine has a broken tab.
Thanks,
Mike
Last month me and the wife took a trip down to Austin. We had been looking for an 80 and figured we should check the local adds and see if any were for sale in the Austin. Well anyway we found a 1994 FZJ-80 that the wife really liked so she bought it. Some of you may have seen it at the...
Dana 60 low pinion rear axle housing. Centered pinion. Ford big bearing housing ends already installed. Using Moser engineering 35 spline shafts this housing will work out to 58.5" wide wheel mounting surface to wheel mounting surface. Shafts are not included.
$250 OBO
In minnesota
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.