Search results

  1. 7

    ICON Cruisers Eucalyptus paint code

    Can anyone help me out with a paint code for ICON Cruisers eucalyptus? Pretty pretty please. Thanks guys.
  2. 7

    For Sale 1978 FJ40 parts

    Seat is sold
  3. 7

    For Sale  1978 FJ40 parts

    Front seats with headrests, seat frames and center console. $300 Radiator mount / support $70 Metal fuel tank with new sending unit $150 Metal fuel tank shroud / cover $150 Original gauge cluster $200 New poly fuel tank in box $150 If these prices are way off please let me know. I don't...
  4. 7

    Full width Chevy axle help leaf help

    Thanks guys, I got some flatter, shorter jeep :censor: springs . Ill see if i cant get them to work with rear shackles. If I cant I'll cut my spring mounts off and run front shackles.
  5. 7

    Full width Chevy axle help leaf help

    If you think the ride would be similar, forward shackles would help correct my caster
  6. 7

    Full width Chevy axle help leaf help

    Yes, I was trying to put the shackles in the rear and cant get the caster angle close enough. My springs have a 10" arch but arent rated that high so they should flatten out some. Everything I have been able to find on front shackles says the ride is rougher as the tire moves forward so I was...
  7. 7

    Full width Chevy axle help leaf help

    If I ran shackles on the front it would be close to fixing the bad angle. I am just worried about a rough ride
  8. 7

    Full width Chevy axle help leaf help

    GLTHFJ60 thanks for the advice. Ill see if i can get the caster closer with a flat/shorter spring
  9. 7

    Full width Chevy axle help leaf help

    My problem could lie in the springs im trying to use up front as they have a significant arch to them with no load, (fforward offset pin) causing my spring to point the diff downward. What springs did you use glthfj60? I assume something flatter and shorter than what I tried. I am using a 54"...
  10. 7

    Full width Chevy axle help leaf help

    My spring pad is cast in so regardless of where I set my caster after a cut and turn, my pinion will still be pointed too far down
  11. 7

    Full width Chevy axle help leaf help

    Is there no way to put Chevy axles under an FJ without cutting and turning knuckles? I know its been done. What am I missing? Who's build should I look up guys? If I cut and turn knuckles, my pinion is still going to be pointed at the ground.
  12. 7

    Full width Chevy axle help leaf help

    Putting a spring over Dana 44 up front. Spring pad centers are 32" wide. I cant put the shackle end of my spring below the frame because it throws my caster way off. I cant outboard the mount higher up the side of the frame because the frame width is the same width I have between my springs and...
  13. 7

    Dana 44 with power steering

    Nothing against the scout box, just looking for alternatives in case my junk yard doesn't have one. Thx Buickguy
  14. 7

    For Sale 40 and 60 parts

    Bump, some parts sold
  15. 7

    Dana 44 with power steering

    Does a box mounted outside the frame rails help with steering shaft clearance? What about pitman arm clearence with the tire? Is there a non scout box that mounts outside the frame rails?
  16. 7

    Dana 44 with power steering

    I guess I was confused. Why isn't it called a Chevy power steering conversion then? The Saginaw conversions ive seen are mounted inside the frame rails, can one be mounted outside the frame rails?
  17. 7

    Dana 44 with power steering

    If i go to crossover is there any complications with running a mid 80's Chevy box? What is the advantage of the Saginaw box over one of these
  18. 7

    Dana 44 with power steering

    Leaf sprung with 37's.
  19. 7

    Dana 44 with power steering

    Full width. Soa. Axle pushed forward about 5"
  20. 7

    Dana 44 with power steering

    I was just trying to avoid buying all the cross over stuff and having to have my knuckles machined
Top Bottom