After the lc100 version gets finalized are there plans to roll out the lx470 version?
Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
I ordered the wiring harness Ben suggested, but had to cut and modify a bit to fit an aftermarket inverter. I believe this part is for a factory inverter. Also, the harness is small. I had to extend the wires to reach where I wanted to install the inverter.Thanks Ben. I've got a 1000W inverter installed - just curious how folks are wiring this outlet to it.
For folks interested in foglight housing for LX470 bumper, please reply with what LED lights you would use. And any requirement you have. Thanks.
Good setup but three on each side leaves no room for the printed mount.This is how 3 diode dynamics ss3 pods fit into the opening, perfect with almost no room to spare
View attachment 3294132
View attachment 3294133
View attachment 3294134
I’d like to order an M46V1. Please advise as to order protocol.In stock
M59V1 Tan
M60V1 Tan
M37 X2 in Carbon Black
M19V1 Blemish
M19V1
Definitely interested in these when available. Nice work!I've collaborated with Mike @98hundy on the development of a foglight mount for Diode Dynamics SS3. Today, he received the prototypes and I have some pictures to share.
View attachment 3280436
View attachment 3280437
View attachment 3280438
Definitely interested in these when available.
Which mounting version did you order? Was there a standard connection for the LC100 that you were able to utilize?
Which mounting version did you order? Was there a standard connection for the LC100 that you were able to utilize?
Which mounting version did you order? Was there a standard connection for the LC100 that you were able to utilize?
Builds - Benjamin’s 3D Prints Build
For folks interested in foglight housing for LX470 bumper, please reply with what LED lights you would use. And any requirement you have. Thanks. Uhm ANY!!! Saw @Natchez suggest squadrons, I'm fine with those tooforum.ih8mud.comBuilds - Benjamin’s 3D Prints Build
For folks interested in foglight housing for LX470 bumper, please reply with what LED lights you would use. And any requirement you have. Thanks. Uhm ANY!!! Saw @Natchez suggest squadrons, I'm fine with those tooforum.ih8mud.com
Hey @BenCC , will the 1.6ft cable be enough? ThanksMake 1: Scangauge II Mount for Toyota Land Cruiser 100 Series
1.1 Overview of the Final Product
View attachment 2299653
View attachment 2178512
View attachment 2178513
1.2 Introduction
First thing I made is the Scangauge II Mount for Toyota Land Cruiser 100 Series. I have been trying really hard to mount the scangauge in my 2000 Land Cruiser. Before I had the mount, it was on my dash behind the steering wheel, attached by a Velcro strip. But it blocked the very bottom portion of the dash. And most importantly, it did not look factory. At the same time, the blank panel on the overhead console has been there forever. It might be a good location for the scangauge.
1.3 Design and Fabrication
The most challenging work is to match the curved surfaces on the bottom of the overhead console.
View attachment 2178507
Multiple parts have been printed to perfect the fitment.
View attachment 2178508
1.4 Purchase List to Complete the Installation
To complete the installation, the following items will be needed.
Ethernet Cable Extender Adapter
Ethernet Extension Cable (Up Angle)
For a smooth finish, you will need:
3M Bondo 801 Professional Glazing and Spot Putty, 3.0 oz.
Note: Dry sand only. The printing material will warp if exposed to excessive water.
Paint
1.5 Purchase Link
$75 + USPS Priority. PM for Direct Paypal Payment.