OTRAM Step by Step Timing Belt Replacement Video Instructions - DIY (Toyota 2UV-FE, 4.7l V8) (2 Viewers)

[BnvS]

Dear Friends, Here is yet another timing belt installation DIY step by step you can follow. In my case I used Otrams Videos which were very helpful in getting the TB removed and installed back up.

I took the time to get the time stamp from each step of OTRAM's videos so you can click on specific time stamp and jump to that step.

Additionally I tried to document all the Nuts/bolts/screws, screw sizes and torque settings for each components that needs to be taken off.

The full link to the file is below - Toyota 4.7l V8 Timing Belt Replacement Procedure. The link also has some more images that would be valuable in the installation process to understand. I.e. the placement of certain nuts/bolts etc.

Timing Belt Spreadsheet - Please comments and I'll add any additional comments to spreadsheet as needed

I will copy the steps below just so if this file is not accessible then you can at least see the steps.

Let me know what you think.

Thanks to all who have helped via this forum.

Official TB instructions from a 2006 Tundra also attached below (should be very similar to the LC/LX)

P.S. BTW I am not sure if Otram is on these forums or not I see @OTRAMM so hope thats you buddy.

 

[BnvS]

TB Removal Instructions

	Removing Timing Chain Steps using Otram's channel	ALL INSTRUCTIONS are you FACING the ENGINE
	REMOVAL Video - Official OTRAM Video is here -
	Part List if you need it. -
	Toyota 4.7 Liter Timing Belt Replacement - OTRAMM - https://www.otramm.com/47-liter-timing-belt-replacement.html
	Steps	Video time link		Comments/Notes with Bolt/Nut Type
	Taking radiator & Fan out would be advisable but not necessary
	- Disconnect the negative terminal of the Battery
1	1. Remove Fan			4x12mm SERATED nuts (around fan bracket studs) - See video to see technique on how to take it out Keep the 4 SERATED 12mm nuts from the fan separate from other 12mm nuts
2	2. Fan Brackets
3	3. Serpentine Belt	Toyota 4.7 Timing Belt Part 1 (updated) - https://youtu.be/4dO8KW1-NQs?t=216		Draw arrow pointing right (clockwise) on belt first to know how the belt turns, then take 14mm ratchet on tentioner pully and turn left (facing engine) to remove the belt
3a	- Remove Fan bracket Pully off	Toyota 4.7 Timing Belt Part 1 (updated) - https://youtu.be/4dO8KW1-NQs?t=282		also take off fan bracket pully off as it is on there loose since we took the fan off with the 4x12mm nuts
4	4. Remove coolant pipe with Hose tubes with attached from water pump to Oil housing/filter	Toyota 4.7 Timing Belt Part 1 (updated) - https://youtu.be/4dO8KW1-NQs?t=284	Toyota 4.7 Timing Belt Part 1 (updated) - https://youtu.be/4dO8KW1-NQs?t=309	- 1x10mm akron nut top next to throttle body hose, 1x10mm bolt bottom on fan clutch (bottom right) watch video on taking the 3x hose clamps off - 1 on water outlet, 1 going to throttle body, one bottom going to oil cooler
5	5. Thermostat Housing	Toyota 4.7 Timing Belt Part 1 (updated) - https://youtu.be/4dO8KW1-NQs?t=351		- 3x12mm nuts
7	6. Top Water outlet nuts - Then wiggle/twist it out cause it maybe stuck	Toyota 4.7 Timing Belt Part 1 (updated) - https://youtu.be/4dO8KW1-NQs?t=367		- 1 x 3in 12mm bolt on top back upper left, 1 x 12mm 1.5in bolt top back upper right
8	7. Remove Drive belt Idler pulley			- 14mm Bolt and cover plate
9	8. Left Cam plastic cover	Toyota 4.7 Timing Belt Part 1 (updated) - https://youtu.be/4dO8KW1-NQs?t=400		1x10mm acorn nut & 3x10mm 1.5in bolts
10	9. Power steering pump - No need to take it out, just remove 3 bolts and Swing it to the side	Toyota 4.7 Timing Belt Part 1 (updated) - https://youtu.be/4dO8KW1-NQs?t=480		3x14mm 4in bolts
11	10. Alternator - Disconnect negative terminal of battery 1st - Slide it off & Swing it to the side as well	Toyota 4.7 Timing Belt Part 1 (updated) - https://youtu.be/4dO8KW1-NQs?t=525		2x 14mm upper and side nut, 1x 14mm 4.5in bolt bottom
12	11. Upper left/middle plastic cover	Toyota 4.7 Timing Belt Part 1 (updated) - https://youtu.be/4dO8KW1-NQs?t=591		- 2 x 12mm 4in bolts
13	12. Tensioner - slides off studs	Toyota 4.7 Timing Belt Part 1 (updated) - https://youtu.be/4dO8KW1-NQs?t=600		2x12mm nuts (top and midlower left), 1x12mm 4in bolt
14	13. unplug Cam Position sensor - Right side and remove rubber grommit	Toyota 4.7 Timing Belt Part 1 (updated) - https://youtu.be/4dO8KW1-NQs?t=635
15	14. Right Cam Gear plastic cover with cam position sensor wire fishing	Toyota 4.7 Timing Belt Part 1 (updated) - https://youtu.be/4dO8KW1-NQs?t=697		4x12mm 1.5in nuts (already took the acorn nut out with coolant hose pipe step 4 above)
16	15. Remove Fan bracket - Remove AC comp Side bolts in front - 2x14mm 4in Top and bottom front bolts (see pics) Loosen back bolt on AC to pivot it enough to remove fan bracket	Toyota 4.7 Timing Belt Part 1 (updated) - https://youtu.be/4dO8KW1-NQs?t=710 Toyota 4.7 Timing Belt Part 1 (updated) - https://youtu.be/4dO8KW1-NQs?t=726 (Ac bolt locations) Toyota 4.7 Timing Belt Part 1 (updated) - https://youtu.be/4dO8KW1-NQs?t=745 (Back bolt location - DO NOT TAKE IT OUT - Just loosen it)+ Toyota 4.7 Timing Belt Part 1 (updated) - https://youtu.be/4dO8KW1-NQs?t=799 (top front bolt location)		2x14mm bolts on front side of ac compressor, LOOSEN only back bolt 1x14mm on ac compressor rear (for me it was eaiser to take drivers tire off and through that side space using Small/medium Swivel socket remove both the bottom front ac bolt and loosen the back bolt) Just keep bolts/nuts together on the fan bracket here to track them - TOO many bolts and nuts hear to track, 12mm and 14mm here
17	16. - Loosen AC compressor	Toyota 4.7 Timing Belt Part 1 (updated) - https://youtu.be/4dO8KW1-NQs?t=745		- 2 x bolts on ac front (Top & Bottom - Make sure you do not remove the AC bracket bolt which is close to the bottom front bolt) and -- Only loosen rear bolt 1 x bolt the rear bolt to pivot AC (Come from driver side opening) this is still a PITA but can be done. Use Small/medium Swivel socket - uplug the ac connector & bend bracket to take it out
18	17. HERE YOU ALIGN THE TDC (Top Dead center)	Toyota 4.7 Timing Belt Part 1 (updated) - https://youtu.be/4dO8KW1-NQs?t=950		crankshaft bolt - 22mm socket on to move TDC - This has to be aligned depending on your Year the TDC arror has to be pointed differently - First rotate it to cranckshaft mark to 0 on the timing cover mark. - Ensure the marks align with 0 and 2 camshaft mark lines (NOT with T) if not aligned move it another rotation to get the 0 (timing cover & crankshaft) and lines aligned on 2 camshaft gears and camshaft cover - then for 2000-2001 LC move crankshaft another 50 deg to so crankshaft mark aligns with middle bolt of the red pully- https://youtu.be/4dO8KW1-NQs?t=1024
19	18. Remove Crankshaft pulley	https://youtu.be/4dO8KW1-NQs?t=1068		- Ensure you are still aligned with the Crankshaft mark so your valve and such are aligned - Use torque gun to take the crank bolt out (check alignment before fulling taking out) - I used a wd40 or similar oil to spray in the middle where the bolt is of the crank pulley and let it sit for few minutes, Then used short wooden 2x4 and hammer and hit the crank pulley at different angles to get it lose. Keep at it, its not the fastest method. You may have to do this a few times to work.
20	19. Remove camshaft timing plastic cover	https://youtu.be/4dO8KW1-NQs?t=1230		4x10mm bolts
21	20. Remove timing sensor guide plate	https://youtu.be/4dO8KW1-NQs?t=1267		it is concave when removed so ensure it’s the same position with putting it back in
22	21. Removing Plastic Triangle	https://youtu.be/4dO8KW1-NQs?t=1296		my car did not have this - Ensure Timing belt is still aligned properly
23	22. Remove the Hydraulic timing belt tensioner	https://youtu.be/4dO8KW1-NQs?t=1332		2x12mm bolts from the bottom - loosen them evenly
24	24. Remove Timing belt off	https://youtu.be/4dO8KW1-NQs?t=1417
25	25. Remove Idler pully #2 (Red one)	https://youtu.be/4dO8KW1-NQs?t=1437		1x14mm bolt
26	26. Remove Tensioner Idler Pully #1 black - above timing belt tensioner	https://youtu.be/4dO8KW1-NQs?t=1485		10mm hex - MAKE SURE YOU GET the WASHER and kept it safe
27	27. Slide the Timing belt pully off	https://youtu.be/4dO8KW1-NQs?t=1518
28	28. Remove Cam Sensor trigger	https://youtu.be/4dO8KW1-NQs?t=1562		1x12mm nut top , 1x12mm long stud bottom lower hold of sensor
29	29. Remove Water Pump - need to twist/wiggle it out at times	https://youtu.be/4dO8KW1-NQs?t=1549		too many bolts/nuts to keep track, so just take it out and keep the nuts and bolts on old water pump. And put while putting in new water pump just transfer bolt/nuts from old to new pump

 

[BnvS]

TB Installation Instructions -

	ALL INSTRUCTIONS are you FACING the ENGINE
	How to install timing belt back on Toyota 4.7l engine 2UV-FE 2UV FE
	INSTALL VIDEO reference - Using Otrams video reference -
	Steps	Video time link	Comments/Notes with Bolt/Nut Type
1	Slide Crank Pully in keyway
2	Clean Water Pump Area with scraper and green scuff pad (scotch bright pads)	Toyota 4.7 Timing Belt (updated) Part 3 - https://youtu.be/GiOgACPh68k?t=331	Easier to clean Waterpump area now - Slightly different order form the OTRAMs video..
3	Install Water Pump Gasket	Toyota 4.7 Timing Belt (updated) Part 3 - https://youtu.be/GiOgACPh68k?t=375	Easier to clean Waterpump area now - Slightly different order form the OTRAMs video..
4	Install water pump pipe o-ring (put a little bit of silicone to make WP seat properly)	Toyota 4.7 Timing Belt (updated) Part 3 - https://youtu.be/GiOgACPh68k?t=380	Easier to clean Waterpump area now - Slightly different order form the OTRAMs video..
5	5. Install Water pump	https://youtu.be/GiOgACPh68k?t=420	One nut and 2 stud bolts = Tq 12ft, all other aBolts Tq 15ft - Transfer nut/bolds from old water pump to new water pump
6	6. Install Idler Pully #2 (Red one)	Toyota 4.7 Timing Belt (updated) Part 3 - https://youtu.be/GiOgACPh68k?t=584	Tq 25ft -1 x 14mm
7	7. Install Tentioner Pully #1 (Black) with washer	Toyota 4.7 Timing Belt (updated) Part 3 - https://youtu.be/GiOgACPh68k?t=242	Tq 25ft 1 x 10mm hex (MAKE SURE YOU INSTALL THE WASHER behind the pully)
8	8. Install Plastic triangle	Toyota 4.7 Timing Belt (updated) Part 3 - https://youtu.be/GiOgACPh68k?t=625	If you have one. My car didn’t have one.
9	9. Install Timing belt	Toyota 4.7 Timing Belt (updated) Part 3 - https://youtu.be/GiOgACPh68k?t=655
10	10. Double check Camshaft marks - Crank shaft timing marks again	Toyota 4.7 Timing Belt (updated) Part 3 - https://youtu.be/GiOgACPh68k?t=880
11	11. Install Hydraulic Timing tensioner	Toyota 4.7 Timing Belt (updated) Part 3 - https://youtu.be/GiOgACPh68k?t=892	- tq 19ft - 2 x 12mm (evenly install these bolt up)
12	12. Ensure timing belt is installed correctly with the correct Cam and Crank marks	Toyota 4.7 Timing Belt (updated) Part 3 - https://youtu.be/GiOgACPh68k?t=982	make sure your L-R Cams gear lines are aligned with timing belt signs L-CAM (Drivers side) and R-Cam (Passenger side) on the timping belt. These don’t have to line up with valve cover cam lines yet. As long as the Timing belt L-R-Cam lines are lined up with L-R Cam gear lines we are good at this time
13	13. Pull the tensioner Pin out of timing tensioner	Toyota 4.7 Timing Belt (updated) Part 3 - https://youtu.be/GiOgACPh68k?t=1035
14	14. Put timing keyway Gear disk (Timing way key gear) - MAKE SURE Concave side out	Toyota 4.7 Timing Belt (updated) Part 3 - https://youtu.be/GiOgACPh68k?t=1051
15	15. Install Crankshaft plastic timing cover on	Toyota 4.7 Timing Belt (updated) Part 3 - https://youtu.be/GiOgACPh68k?t=1075	- 4 x 10mm Bolts - Tq - Good and tight
16	16. Install crankshaft timing pully (dampner pully) line it up with the Keyway	Toyota 4.7 Timing Belt (updated) Part 3 - https://youtu.be/GiOgACPh68k?t=1115	- 1x22mm - Tq 181 ft (one hundred eighty one ft)
17	17. Double check timing is good again	Toyota 4.7 Timing Belt (updated) Part 3 - https://youtu.be/GiOgACPh68k?t=1135 - https://youtu.be/GiOgACPh68k?t=1160	Here move your camshaft pully mark to 0 on the timing cover. The L-R Cam Gears Lines, will align up with the Valve Cover Lines (similar to when you were aligning the Timing belt to take it off - NOT the T mark)
18	18. Install Serpentine belt tensioner (upper left)	Toyota 4.7 Timing Belt (updated) Part 3 - https://youtu.be/GiOgACPh68k?t=1262	- Tq 12ft - 2x12mm nut on top and side (non serated ) - 1x12mm long bolt (~3in) on bottom
19	19. Install Alternator bolts back	Toyota 4.7 Timing Belt (updated) Part 3 - https://youtu.be/GiOgACPh68k?t=1348	- Tq 29ft - 1x14mm nut top 1x14mm 2.5in bolt bottom
20	20. Install Power Steering pump	Toyota 4.7 Timing Belt (updated) Part 3 - https://youtu.be/GiOgACPh68k?t=1401	- Tq 13ft - 3x14mm 3in bolts
21	21. Install Fan pulley bracket - Make sure wiring is tucked back properly - Make sure it sits without rocking	Toyota 4.7 Timing Belt (updated) Part 3 - https://youtu.be/GiOgACPh68k?t=1497	- Tq 12ft for 12mm nut (top)/ bolt (right above 14 nut (right most) - Tq 24ft for 14mm nut(right most side)/bolt (lowest side)
22	Put AC bracket back on the fan bracket	Toyota 4.7 Timing Belt (updated) Part 3 - https://youtu.be/GiOgACPh68k?t=1663
23	22. AC compressor bolts - put long 2x14mm bolts from side (top and bottom) onto the fan bracket - Likely need a swivel socket wrench to tighten front bottom bolt. - Tighten back ac bolt Tq = 36ft for all 3 bolts	https://youtu.be/GiOgACPh68k?t=1660 and put in ac bolts back up	- Tq 36ft - 2x14mm long bolts from the AC comp side that go into the fan bracket side (if your fan bracket is not sitting properly you will not be able to align these 2 side bolts properly - Ask me how I know ) - 2x14mm long bolts on side of AC compressor - 1 on top side and 1 on front bottom) See where OTRAM is putting in these 2 bolts slowly and rewatch. (Top & Bottom - Make sure you do not remove the AC bracket bolt which is close to the bottom front bolt) and -- 1 x bolt tighten the rear bolt that was loosen to pivot]
24	- Snap AC Compressor wiring back on
25	23. Install Cam postion sensor	https://youtu.be/GiOgACPh68k?t=1750	- Tq German Good and Tight
26	24. Install Right side Cam belt cover - Fish Cam sensor and Gromet through the cover	https://youtu.be/GiOgACPh68k?t=1840	- Tq 16in lbs - 4x 10mm bolts
27	25. Install Water pump plastic cover	https://youtu.be/GiOgACPh68k?t=1955	- Tq 12ft - 2 x 12 mm 4in Bolts
28	26. Install Left Cam belt plastic cover		- Tq 16in - 3x 12mm bolts, 1 acorn 12mm nut
29	27. Clean Water outlet Inlet and on water outlet part with razor, wire brush of old FIPG, degrease the area both side
30	28. Install Thermo water outlet - Put Outlet O-Ring on little bit of Silicon Grease - Clean surface of Water outlet (old FIPG clean with green pad/razer blade wire brush the surface) put new FIPG gasket maker on	https://youtu.be/GiOgACPh68k?t=2094	- Tq 15ft - 1x 12mm 3in on left top bolt, 1 12mm 1.5in bolt right side
31	29. Install water outlet pipe	https://youtu.be/GiOgACPh68k?t=2366	- Tq German good and tight. 1x 10mm acorn nut on top - 1 10mm bolt bottom - Put the 3 hose clamps back to original position - 3x hose clamps off - 1 on water outlet, 1 going to throttle body, 1 bottom going to oil cooler
32	30. Install top idler pully	https://youtu.be/GiOgACPh68k?t=2451	- Tq 27ft - 1x 14mm nuts
33	31. Install Thermostat with Thermostat Seal - Ensure if you have Toyota Thermo that the Giggle valve on the 12 O'Clock position	https://youtu.be/GiOgACPh68k?t=2511	- Tq 12ft - 3 x 12mm bolts
34	32. Install Fan pully cover	https://youtu.be/GiOgACPh68k?t=2600	Otram did not install on video
35	33. Install Serpentine Belt (see diagram on your hood sticker or to the side)		Otram did not install on video
36	34. Install Fan		- 4x12mm serated nuts on similar to how you took them out
37	35. Install Radiator if you took it out
38	Put in new Coolant
	- Reconnect the negative terminal of the Battery before starting

 

[97 AZ LC]

Good job, thanks. This should be linked into some of the other timing belt threads so that people can find it.

 

[AlpineAccess]

Legend

 

[e9999]

Very nice!
I added this to the FAQ, don't change the thread name in case it throws the link off.
If somebody wants to add some time estimates for the whole thing and/or main steps, that would be great!

 

[BnvS]

Thanks @e9999 I'll make sure I'll keep the topic the same...

I didn't add time estimates b/c time is really dependent to the person's experience. This took me 4 days to do at a steady pace.. If I have to do it again I would be able to do it in say 2 days. But I am sure someone more experienced may be able to do it in one day.. If in doubt slow and steady wins the race..I say.

 

[OffRoadRN]

Thank you so much!

 

[BnvS]

Deleted. posted on wrong chat

 

[98100Crusher]

A note on step 7 of the install: you should seal the tensioner pulley pivot bolt threads.; if you don't you get an oil leak. FSM specifies adhesive including blue loctite 242. The updated video(engine out of truck) doesn't have this step but the old video(part 2) did.

 

[JimSoCal]

A note on step 7 of the install: you should seal the tensioner pulley pivot bolt threads.; if you don't you get an oil leak. FSM specifies adhesive including blue loctite 242. The updated video(engine out of truck) doesn't have this step but the old video(part 2) did.

This is a step I think most people skip (myself included in the past) that causes a very slow oil leak, that often gets diagnosed as a front crank seal leak or oil pump leak.

You can also buy a new bolt that has sealant on it already I believe. Seems like a very odd design to have the hole threaded through the oil pump, but I assume it was a packaging thing.