Start with painters tape to isolate the whistle. Btdt. Glass half full moment. Your annoyed by a whistle at speed, which means your driving it. Better than most in the forum.
Gonna guess I'll be early and stay late. Prob 1.5 people. I'll try to keep the .5 out of the pond but I apologize in advance because she really likes that pond.
Took my 40 out for a little drive for the first time in a couple of years. The weather was too nice not too!
I was waiting on some exhaust parts to come In so I shoved a stove pipe to get the exhaust out from underneath. Too loud for me with an...
Here is the completed power steering line…. Compression fittings on both ends, that are the original Toyota lines…. Just had a couple hours in the shop tonight, but I got that power steering line in and the transmission lines in to cooler…. Baby...
Goals to have the 100 rolling again? Without deadlines nothing gets done. I'll put in my pto request. Do they have cabins now? Asking for the old guy that I somehow became.
Or the southern cruiser crawl in Oct at the same park. Or both?
Completed commemorative art project.
Signatories are the crew who pulled me out and took care of me. I could not have run with a better crowd.
Shout out to: @tornadoalleycruiser, @1994pd, @2fpower, @kc_chevota, and @StucknKS.
just talked to @kc_chevota and he said that the 2 other wires to the compressor are not needed. Evidently the compressor has a second pressure switch in it that are not needed.
You should double check your overflow tank cap to ensure the hose connected to the radiator neck dips down to the bottom of the tank, and the other hose is connected to the vent at the top of the tank.
Also, it appears you have a valve on your...
Nice looking rig. Re: taking your rig to the dealership, I’d be very careful- those techs are not gonna be up to speed on working on a 75 carbureted rig. Much better to find a local specialty shop (expertise and price wise) or even a mom and...
I believe u are correct and the hurricane signal to the clutch I believe goes to the idle up. Not sure what the other stuff is in the main harness unless some eco mode turns off the ac or full throttle turns off ac.
Some older fj40's had a tube going down the side of the radiator and did not have a catch can. If the dealer didn't drain the block thus doing a proper flush you might have incompatible coolants jelling up, might need to be burped, might have a...
I like the flat splicer, two reasons, one is every synthetic line I've ever taken apart doesn't have enough bury of the end on the splice, and two, it eliminates a potential pin failure. I have a line spliced already with a flat splicer for the...
I am currently running soft valved bilsteins. Tried a set of emus and way too stiff. I would not hesitate to get a set of these springs and probably will later. I just need to put miles on the 45 before I justify any other expenses on it. I have...
The deja vu this is why im interested. I have a set of the tic parabolics, the set chef had that were referenced in the other thread were too short. I sorta ended up with 2 sets to make one out of, Chefs and my own set we imported. I'm watching...
? B4 u go too far, need to set the ac box in there and insure the hoses will turn and clear before you put them on a panel like that. Where are the other 2 ac vents going? I might have some extra vents here to help layout. I'll dig and put them...
Paul, u still need a corner? I think I saw spares at the other house a few weeks ago. I think the reason we didn't use them was a few scratches and weld splatter marks. If you don't find one let me know. Wasn't planning on getting rid of spares...
The Egypt one should work. I had to find one overseas to fit chefs 45. Might b easier to see if someone has a 3spd floor shift conversion lying around for sale cheaper
I'm away from my vehicles. But, the tall 40 puck by running boards, then a circular one between back cab mount. I can snap pics this weekend with measurements. Front 40 mounts under bib, running boards, and front of cowl, 55 style back of cab...