Obrokoff
Latest activity Postings About Badges Post areas
-
-
Obrokoff replied to the thread Builds Airbagged 80 series on 42 inches. Low cost Russian build thread.Yes. But I can swim to Alaska through the Bering sea 🤣 -
Obrokoff replied to the thread Builds Airbagged 80 series on 42 inches. Low cost Russian build thread.Aftermarket controller like a accuair works better than stock and give more diversity in setting up several levels
-
Obrokoff replied to the thread Builds Airbagged 80 series on 42 inches. Low cost Russian build thread.Height sensors not a problem. I can buy it from china
-
-
Obrokoff replied to the thread What’s everyone driving when you leave your LC home?.Another legendary car Mitsubishi Lancer Evolution
-
-
Obrokoff replied to the thread Builds Airbagged 80 series on 42 inches. Low cost Russian build thread.Really hard to realise this option. I think it’s don’t need to 4x4 rig. Accuair controller with height sensors in my future upgrades. But I can’t buy it from USA now.
-
Obrokoff replied to the thread Builds Airbagged 80 series on 42 inches. Low cost Russian build thread.Yep, me too 😂
-
Obrokoff replied to the thread Builds Airbagged 80 series on 42 inches. Low cost Russian build thread.This is a good option of air springs. I use it when moving along the slope
-
Obrokoff replied to the thread Builds Airbagged 80 series on 42 inches. Low cost Russian build thread.It’s very hard to realise. Who can made this controller?
-
Obrokoff replied to the thread Builds Airbagged 80 series on 42 inches. Low cost Russian build thread.I use Auger 20110, analogue of Contitech sz130-25p05. It’s cheaper than contitech, but works fine.
-
Obrokoff replied to the thread Builds Airbagged 80 series on 42 inches. Low cost Russian build thread.
-
Obrokoff replied to the thread Builds Airbagged 80 series on 42 inches. Low cost Russian build thread.Coil springs not a forever. Most coil after two or three years downsize. After six years on mud and snow air springs like new. Cost of one is about 50usd.
-
Obrokoff replied to the thread Builds Airbagged 80 series on 42 inches. Low cost Russian build thread.Yes, I made new bump stops. Hydraulic bump stops are better, but now I can’t buy it.
-
-
Obrokoff replied to the thread Builds Airbagged 80 series on 42 inches. Low cost Russian build thread.@BILT4ME Yes, change it to new. Old bolts are cut off. they was marked 10.9, but really be 8.8. Buy new rotor, new bolts 10.9, Tightened with a force of 140nm
-
Obrokoff replied to the thread Builds Airbagged 80 series on 42 inches. Low cost Russian build thread.
-
-
Obrokoff replied to the thread What Did You Do with Your 80 This Weekend?.Junkyard antirock sway bar complete. Work fine.
-
-
-
Obrokoff replied to the thread What Did You Do with Your 80 This Weekend?.s*** parts. New rotors, installed two months ago. Less than 1000 km.
-
-
Obrokoff replied to the thread Builds Airbagged 80 series on 42 inches. Low cost Russian build thread.Yes, 8.5mm spacer
-
Obrokoff replied to the thread Best 17" Wheel/Rim Options?.Forged 3 pieces JDM Lodio Drive 17*12,5 -63 offset, no needs spacers
-
-
Obrokoff replied to the thread Builds Airbagged 80 series on 42 inches. Low cost Russian build thread.
-
-
Obrokoff replied to the thread Builds Airbagged 80 series on 42 inches. Low cost Russian build thread.Cheap junkyard torsion sway bar for my 3-linked cruiser. Mitsubishi torsion bar, plasma cutted levers 10mm thickness
-
-
Obrokoff replied to the thread What Did You Do with Your 80 This Weekend?.So sweet 😍
-
Obrokoff replied to the thread Builds Airbagged 80 series on 42 inches. Low cost Russian build thread.Replace PSF tank and hose to steering pump. New from UBS69/73 Isuzu Bighorn. Bigger and better. Removable filter inside. Steering works very well
-
-
-
Loading…
-
Loading…
-
Loading…
-
Loading…
