Kroll

And now on to The Grand Tetons! In addition to a black bear at 25 yards and a cow and calf moose at 100 yards, I spotted this wild beast:

In the Canadian Rocky Mountains of Alberta..... :cool: 🇨🇦

Been a few busy last weeks with getting my 84 pickup back on the road. Finished rebuilding my 22R and installed it. Thankfully I had a spare motor that needed rebuilding since the one I pulled out was in real poor shape after I overheated it on...

Nothing major today I relocated the espar fuel pump closer to the other side now need to get a T to make a junction between the fuel tank and wabasto cooker. Also thinking about an actual hermétic way to get fuel out don’t like the plastic line...

All the coating is done, tape pulled, letting it cure over the weekend. Cheers

Dug through some cruiser stuff and found 2 sales brochures. Some good cruiser memorabilia. Funny how the prices on LV's have changed. LOL.

Recently added a few mods to make the 79 a bit more convenient for getting away for a few nights. With a 3-year-old and a 10-month-old I have really struggled with the sleeping situation. I have always wanted a RTT but it needed to accommodate...

The last few days has been building out FTE swap harness. Unichip with OEM Toyota plugs so it can simply be removed or installed by plugging in these two plugs. ECU wiring. Love this wire we found for projects like this. Everything...

Well, after two years of sitting outside I brought my truck into the shop and my plan is to start ramping up on finishing my engine swap. My goal is to drive it out to Rubithon this year…. Crossing fingers…

You can also buy it from any Toyota dealership. Got mine in 2 days.

Took a break from the 60 and took the Kawasaki Jet Mate to Mallacoota for a weekend. It went awesome. I thought i was in some trouble for a bit coz it wouldn't get up on plane. We'd been drinking at the pub for a few hours and still had to get it...

Hello everyone, I just installed the controller into my 1984 bj42 24v Canadian spec. Installation is very straightforward and all literature provided is very concise and accurate. The factory harness connection needs to be swapped as they are...

Sooooo After my last tests I made a 3rd version of my superglow electronic replacement. I fixed all identified hardware bugs and made global improvements (stability, power supply variations,...). I added a wilson switch port that does not need...

Hi guys and galls Im new to the forum. I drive a 2006 HZJ79L in Curacao which is a caribbean island north of venezuela. Thanks for letting me join!

Japan4x4 - Talk to Dave

Nice man, your gunna end up with a pile of 1vd belhousings with no home😄

Nice. I got one too recently…

The certification issues are due to diesel engines for LC applications. Toyoda Industries cooked the books.

Well I'm home for spring break for the next 10 days or so, thus I have access to a garage and welder! Well my quarter panels have had rust popping up on them for the past 2-3 years now, I grind it down, convert it, paint it, and it returns in a...

A special package arrived from Japan.

Hello, Chance's indicators began to act erratically. I checked for bad grounds, and found a stripped wire. The pervasive legacy of alarm installers. I repaired it, but the problem persisted. The combination switch is fine, and the rest of...

Did a h152 to h151 a week ago. No issues. Cheers

This time I put the transmission into first gear so I can wiggle the rear output to wiggle the input shaft to fit into the splines on the clutch and into the pilot bearing. Tomorrow should be done with putting everything back together and fill...

The 3D scan is in hand, drawings are underway! Will have to bolt the crossmember up to the transmission again and check the angle the transmission sits at.

I thought about going with this method but don't have a good way to transfer the center of the input shaft to the plane of the belllhousing mounting surface. According to various engine/transmission manufacturers there needs to be less than...