GXO's latest activity

Bump again for the lowest price. Let's go!

I mean, he is going to retire soon. I could sponsor him and hire him out haha

Bump, updated price (lower).

My FIL decided he wants to spend some time in GA this spring so he is coming down and will be looking at the BJ60 as a project. Works for me! He is a master level diesel mechanic and has owned and worked on BJ60s in Canada for decades. Lucky...

That's a 3b all right :lol:

Someone asked me if I had the OEM awnings available. The easy answer: I would never do that to you. They are horrible. They take forever to setup and weigh a metric ton and also won't stay waterproof or store well at all. I cut off...

This thing ran like a champ till it didn't. I took out the veggie system and cleaned up what I could....but I have more to do.

I am hoping I am home for a while so I can get into the search! I am certain it is a massive air leak.

The air suspension and shock controller is in a slot that is the same as the 100 series console. You just have to get that part and pop out the controls and pop in the cup. There is also a flat plate that can be used if you want to use it for a...

Got the cleanup done. Going to replace my grip tape on the lower rocker as it has peeled (I cover the clip holes with tape). I also need to finish my cutting and tacking sheet metal. Wife's GX repair is taking the lead on priority right now.

I would do a few things....one, I would continue to drain and fill the ATF more frequently. You are basically running on burnt ATF and the dirt is in the valve body. So, you have a few options, and what I would do: 1. Pin your transmission...

$22,000. We received our new trailer and shook it down and need to get this gone. This is likely the best deal on a Conqueror you will see. Located in north Georgia. Can tow to meet you somewhere if you like (no charge to AL, TN, NC, SC)...

I assume it is cold. How old is the fluid? Drain and fill every oil change for the next 4-5 oil changes usually clears up viscosity breakdown.

filter is clean and new.

Thanks all. I will keep hunting the fuel and walk the lines and check the tank. I just have to find time now :)

Will do. A quick test. Looks like I need some diesel!

I bled the filter and pressurized it with primer and bleeding. I have fuel in the filter but not getting fuel to the injectors. I have shown combustion with ether so it will turn over. I feel like I have a fuel line tank to lift pump or...

We have a 1983 BJ60 LHD Canadian G spec BJ60 with a 3B with an H55F behind it. We were driving home and the truck started to lose power while driving (like it had a lot to start with). I was pushing hard to keep it running and revved up the...

Teaching the wife may be a good idea - Mrs. Rednexus is far more detail-oriented and better at artistic things than me (and let's face it, welding is really an art). She's definitely better at things like applying silicone,, caulking trim, etc...

I need to look into it. I have a couple things I want to weld onto the GX470 (EimKeith LLS, oem factory cam tabs)

I got started with a $200 HF Titanium 125 flux core welder. Bought it as an emergency purchase to get stripped studs out during my header install. It lasted ~2 years before crapping out but it let me do a lot of small-scale welding including...

I love that she is learning to weld. I plan to improve my welding as it has been a few years. We have a lot of welding to do on the BJ60 haha

Doing some clean up on HP. Got a leaky ARB line to the rear locker fixed (exhaust touched it) and about to cut out more of the rear bumper to make more room for the 37s. Also going to cut and retack the welds on the front fender supports (wife...

oh I suspect the new trailer is going to slow me down and suck a lot more go juice. Trust me haha

Sorry for the pupper loss :(. We are upgrading to 400Ah Renogy self warming LiPo and 400w of solar. Adding wifi therm and other controls as well as soft start on the AC. The rest will be my mods. Starlink mobile and some other networked/wifi...