1998 - 2007 Toyota Land Cruiser Behind Front or 2nd Row Seats Barrier Divider Net - Dual Position- BLACK
NEW - NEVER INSTALLED
$150 Shipped CONUS- ( MSRP $229.00)
More details here...
I bought the Tread 5.5 Base model- literally just ordered it. No direct user experience yet.- I picked the smaller 5.5 Base unit mainly for back country motorcycling and in the Cruiser as needed. At 499 it ticks a few boxes for my needs.
For...
We could pull the front diff and look at the pattern on the gears, check bearing pre load and make sure everything looks okay.. having sat in the truck with you for long distances at those speeds, i doubt its the gear set, but you never know.. i...
Maybe not the front but the axles might be an issue.
Call these guys and talk through it- driveshaft (not your gears)
Drive Line Service Of North Atlanta Inc.
(770) 242-9365
Drive Line Service Of North Atlanta Inc. - Google Search -...
Good questions - 🫤
Yeah 2 post lift- they did this (driveline check) with my F350. So I’m speaking to the 70mph issue specifically, not the other things you listed. Logically (my logic lol) If you’re checking driveline for imbalance, or runout...
Running on a lift- that’s how the big boys do it to isolate NVH & driveline issues-
If you go to the trouble of pulling the diffs- I wouldnt mess with it locally- I’d send them straight off to ECGS -
Regarding the speed related issue that presents at 70mph-
Is it repeatable every time? Audible or mechanical?(heard or felt?) if audible, do you notice droning or resonance? If mechanical where do you feel it- steering wheel, seat, floorboard...
Couple quick videos while I was doing some last minute tuning. Engine work starts tomorrow!!!
Lots of people asked for videos. This was best I could do by myself and not much room to get off the rev limiter in first gear.
Outside of the boot "kit" you'll need 2L of gear lube, a new OEM differential axle seal, new axle end snap ring of the correct thickness, a new locking tab washer, possibly a thrust washer. Depending on the condition and proper/improper removal...
I wanted to share that three of my closest friends and COTR Trail Leaders, Matt Huey (@DeuceDeuse13) , Shawn Pugmire(@Noble Oak) , and Aaron Thorne (@aaronrules) are active military or veteran. I'm honored to have these men as friends and proud...
Your starter is prob fine- it’s up high and in the back so that water cresting the hood prob didn’t get to the starter- if you kept moving.
I’d check the engine bay fuse box and relays for moisture and also all ground wires leading to engine...
Hey Joe-
The platform has pros and cons(like everything we mod on these trucks).
PM Jason he’s probably got a few sets of mounts laying around. The platform I designed and the mounts Jason made for me is intended to securely hold my fridge with...
http://www.americanpaintandbody.com/
I just had these guys do some work on one of my old Mercedes. I just picked up a few weeks ago. IMO, the work is top notch and they're real body guys. They did some very impressive rust remediation/ weld...
4ft-lbf is not the final torque, it's the starting point. Many including I, read FSM wrong. Preload (PL) is the goal, not torque on adjusting nut!
When reading FSM, in the light of; "preload (using fish scale) is the goal". Which I shoot for PL...
While I generally agree with your comment, I suspect the the front driveshaft would be slightly less “dynamic” from a fixed transfer case, to a fixed IFS front differential, then again, I’d still prefer an OE/OEM solution.
This ^ 👍
“…… The battery must be disconnected, and more importantly, the ground clamp of the welder should be mounted right next to the place getting the welding on.“
People using electric welding on modern vehicles should know what they are doing. The battery must be disconnected, and more importantly, the ground clamp of the welder should be mounted right next to the place getting the welding on.
May be...
KIA U joints in a LC? I would never install those cheaply made Korean parts into any of my vehicles. You could have easly sourced OEM U joints or get the entire OEM drive shaft for like $300 during toyota dealer promotion. Besides, front drive...