UPDATES!
I have pricing for the header.
First, thank you all for your interest in our efforts.
Before I go further, remember what @gonzopancho said about labor and materials costs - they are "dynamic", so pricing may change.
Also, I am trying...
🤙
exactly why i suggested making a slip fitting parallel to and past the muffler that allows any end user to add the final "oem" side exit location piece (and even rotate and trim it a bit if needed, or re-route as needed for a modded setup...
Correct that I have 31's, was thinking about going bigger after I get my PS installed but maybe not! This exhaust is perfection and I don't want to mess with it. The setup that you have configured fits stock FJ40's and people that modify their...
@65swb45 brings up a good point, and reminded me of what modifications I had to do to a new exhaust that was installed when I initially purchased my 40. In the photo below, you can see how the mechanic had the exhaust run a little more than 45...
dump exhaust behind rear shock 45* down. no tire or spring concerns. or leave it as a slip fitting end att shock for user to finish
.......though i read comments above and that is a real concern
Follow-ups to a very old thread.
1. Ed left the ice chest that the Fat Tire was in with me as well.
2. That same day, another customer dropped off a carburetor to be rebuilt. Obviously impressed with the karma, when he returned to pick up his...
For sale.
GM SM 465 mated to 1972 3 spd t case. Pulling for 5 spd swap. Runs drives shifts. Includes bell housing.
$900 obo. Not sure what a fair price is.
Denver.
I have a new in the box Marlin Tacobox that should fit any 4 liter Toyota build but I would do my research before you get too deep into this. It definitely fits the FJ and 4Runners of similar years and engine/tranny specs. This unit was built by...
Nitro changed hands a few years ago and it seems popular opinion is their quality has severely dropped off. They used to be my go to gear mfg.
Yukon has a strong warranty and their setup kits are solid. It is the brand i have in my crawler...
New 4X series headlight floor dimmer boots have finally been reproduced! $35 . Made of a tough rubber to stand the test of time and protect the switch contact posts. HERE
1. That is a stock length shackle. You should NOT run a stock shackle with a lift spring; the extra arch of a lift spring requires a wider range of motion than a stock shackle can provide.
2. The offset of the rear spring hanger creates a fulcrum...
Hi guys, just wanted to hop on here as we've seen lots of comments about the retirement to this day. Todd is still looking to retire but we're still in business as usual! Although he's ready to relax, we will continue manufacturing all parts for...
Correct - post #385 is the exhaust system that @Lola333 built.
I do confirm O2 bung in #374, but the @gonzopancho post #126 shows it best:
https://forum.ih8mud.com/threads/fj40-mark-downey-header.1267016/page-7#post-14706817
We wanted to...
i have the Holley in tank pump purchased and ready to install in my LRA 29gal underseat tank. will need to cut access hole of course. Its on the list of projects😂😂😂. But i HAVE it!
Hey all! These are live on the store now. Super excited about these. 63-71 FJ40 FJ45 horn contact ring and brush - https://cruiser-cult.myshopify.com/collections/40-series/products/63-71-fj40-fj45-horn-contact-ring-and-brush
We have 10 in this...
For sale: Tembo Tusk slider cutting board,12"x 18" HDPE cutting surface, slider mounted once but unused, and cutting board still wrapped in original plastic. You can mount this under fridge slider or kitchen box setup, and has a positive...