4X4Labs Bumper Group Buy (1 Viewer)

[davegonz]

So, who's interested in getting a group buy going for 4x4Labs rear bumper kits?

Bumper kit info and welding how-to: https://forum.ih8mud.com/az-copper-state-cruisers/142286-4x4labs-rear-bumper-build.html

• Citadel-80 series rear
• davegonz-100 series rear
• warpdriv-80 series rear
• Cool Breeze-80 series rear

Here's a recent price list:
Rear Bumper Kits

Basic bumper- kit $495 Welded and finished $895
1 main bumper shell
2 sides
2 side top tubes
2 d-ring points
towing crossmember
receiver

Single swing out bumper- kit $895 Welded and finished $1375
1 main bumper shell
2 sides
2 side top tubes
2 d-ring points
towing crossmember
receiver
1 large spindle assembly
1 swing arm assembly with 4 sleeves
Latch and latch plate
1 gas strut with ball stud
2 stoppers

Double swing out bumper- kit $995 Welded and finished $1495
1 main bumper shell
2 sides
2 side top tubes
2 d-ring points
towing crossmember
receiver
2 large spindle assemblies
2 swing arm assemblies with sleeves
Latch and latch plate
2 gas struts with ball studs
3 stoppers

15. Accessories
Tire holder- kit $125 Welded and finished $225
Swing out clamp bracket
Main upright
2 gussets
side clamps
top cap
3 hole tire holder
square tube receiver
3 wheel studs
3 lug nuts
Hardware

One, two or three gas can- kit $195 Welded and finished $395
Swing out clamp bracket
Main upright
2 base gussets
2 tubing hoops
tube spreaders
bottom plates
2 basket gussets
License plate bracket
Hi-lift bracket with standoff

Ladder #1 – kit $150 Welded and finished $350
Swing out clamp bracket
2 Base tubes
2 rungs
Hi-lift bracket with standoff

Ladder #2- kit $175 Welded and finished $375
The first rung on this ladder is sleeved just like the swing arms for a third accessory like gas cans or a cooler. It can be removed for regular access to the ladder.
Swing out clamp bracket
Main hoop- long, you cut
1 round rung
1 square sleeved rung
Hi-lift bracket with standoff

Cooler basket- kit $225 Welded and finished $425
Swing out clamp bracket
Main upright
2 base gussets
2 tubing hoops your supplied dimensions
tube spreaders
bottom plates
2 basket gussets
License plate bracket
Hi-lift bracket with standoff

ARB fridge basket- kit $225 Welded and finished $425
Swing out clamp bracket
Main upright
2 base gussets
2 tubing hoops
tube spreaders
bottom plates
2 basket gussets
License plate bracket
Hi-lift bracket with standoff

Bicycle rack, 2 bikes- kit $195 Welded and finished $295
Swing out clamp bracket
Main upright
2 base gussets
Rear tire plates
Rear tire plate crossmember
Rear tire hold down straps
2 skewer tubes
2 skewers
Safety hook
Top cap
Logo plate

16. Separate bumper parts
*Main Shell- Formed and plasma cut bumper shells for FJ80 and FJ60 $185
*Uncut formed main shells 72” wide- $125
*Formed laser cut side skid plates- $125 ea.
*HD Spindle assemblies- $95 ea.
*Swing out assemblies- HD spindle assembly, sleeved swing arm with gas shock, ball studs and stops - $225 ea.
*Accessory bracket clamp- $25
*Towing receiver- $25
*D-ring tow points- $30 ea.
*Hi-lift bracket- $25
*License plate bracket- $10
*De-sta-co 4000 lb. Latch and latch plate- $95
*Gas struts 120 lb. $25 ea.
*Ball studs $2.50
* 6" or 8" Gusset $9

*Accessory carrier retrofit sleeve/clamp kit- $29


*Using our retrofit sleeve and clamp kit our detachable accessory system can be retrofitted for use with any other rear bumper system with a 2” swing arm (ie. Kaymar, Slee, Man-a-fre, etc.)

 

[citadel]

I am in for sure... I spoke to JK and he can weld it up if I get the kit. He charges by the hour and says it shouldnt take more than 3 hours.
Luke says the kits are ready to be shipped out now.

I was going to go the basic kit route then in the future add on the rear tire carrier and ladder..

When are we pulling the trigger?

 

[davegonz]

I'm in for a basic one 100 series one. We can probably have them shipped to JK's biz address to save money.

 

[citadel]

who can check on the discount we should expect based on volume?

 

[yoda85]

To bad They don't make that for a FJ60

 

[citadel]

ok... Spoke to Luke this AM...

Minimum for a discount is 5 bumpers.
If we have less, we could save on shipping but he says he doesnt think he can discount the bumper price unless we have around 5...
I will be ready to jump in a week.....

Anyone else in?

We could combing shipping from California to JK Customs in Hutto...

 

[davegonz]

I'm in for one bumper. Let's get this rolling.

Curtis, did he give you an idea of how much off he can do for 5 or more?

 

[citadel]

Not really. He said once we have the number of bumpers he could give us a quote.
If no one else is in, you and I could go in and still save on shipping... He said shipping was a little under $150 for a single unit to Texas...

 

[citadel]

ok.. just paid for mine.. looks like Luke is giving Dave and I a 10% discount and combining shipping to JK's.

 

[cool breeze]

wow, good for you guys. That was nice to give you 10percent with only two orders, wish i had the cash right now

 

[davegonz]

ok.. just paid for mine.. looks like Luke is giving Dave and I a 10% discount and combining shipping to JK's.

Sweet!

 

[yoda85]

I am going to call them to day and see if they can make me a rear bumper for my FJ60.

 

[Sea Knight]

ok.. just paid for mine.. looks like Luke is giving Dave and I a 10% discount and combining shipping to JK's.

There's obviously a communication problem here. Allow me to straighten it out. Dave does not buy anything at a measley 10% discount. His rule of thumb is to pay no more than 10% of retail. That translates to a 90% discount, for Dave's bumper at least. The rest of you will have to fend for yourselves.

 

[davegonz]

Follow up on the bumper build: https://forum.ih8mud.com/100-series-cruisers/294772-penny-getting-luked-4x4labs-rear-bumper.html