1st Gen Sequoia middle console switch panel (1 Viewer)

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Currently working with a friend of mine on a 6 slot panel for the middle console. This panel snaps into place like the Oem panel and accepts factory and aftermarket Toyota switches. First print will be done 4/9 and I will test fit and post pics. Here is the rendering for now. It will be printed in black petg with a textured finish on the front flat. Will more than likely be selling these for about $55 shipped. That may change depending on shipping, but I can't imagine much. I will keep this thread updated for reference to the panel from other forums.

***UPDATE*** as of 10/30/21 $55
These are in production now. PM me if you want one. Payment through Paypal or Venmo. $55 shipped.
Have had a few people ask about custom switch locations, ie, pressure gauge, temp gauge less switches... Just need the measurements/layout for what you are wanting and can draw it up. Will be $65 for a custom setup though.

***install instructions***
We made the side clips extra "clippy" so they are a very secure fit. Do your best to have everything ready to go before you put it in. It is very difficult to get your fingers under there to push the clips out. I used AOB switches. Use 2005-2007 Tundra center console as the switch type. There was variation on the clip of the switch from one switch to another, about a 1/64 so we took out that 1/64, you may have to sand a little on the back depending on the tolerance of your switch, but I doubt it.

View attachment 2639727

View attachment 2645535

View attachment 2645542

View attachment 2645543

View attachment 2645544

Currently working with a friend of mine on a 6 slot panel for the middle console. This panel snaps into place like the Oem panel and accepts factory and aftermarket Toyota switches. First print will be done 4/9 and I will test fit and post pics. Here is the rendering for now. It will be printed in black petg with a textured finish on the front flat. Will more than likely be selling these for about $55 shipped. That may change depending on shipping, but I can't imagine much. I will keep this thread updated for reference to the panel from other forums.

***UPDATE*** as of 10/30/21 $55
These are in production now. PM me if you want one. Payment through Paypal or Venmo. $55 shipped.
Have had a few people ask about custom switch locations, ie, pressure gauge, temp gauge less switches... Just need the measurements/layout for what you are wanting and can draw it up. Will be $65 for a custom setup though.

***install instructions***
We made the side clips extra "clippy" so they are a very secure fit. Do your best to have everything ready to go before you put it in. It is very difficult to get your fingers under there to push the clips out. I used AOB switches. Use 2005-2007 Tundra center console as the switch type. There was variation on the clip of the switch from one switch to another, about a 1/64 so we took out that 1/64, you may have to sand a little on the back depending on the tolerance of your switch, but I doubt it.

View attachment 2639727

View attachment 2645535

View attachment 2645542

View attachment 2645543

View attachment 2645544
How do I go about getting one of these? You have fb or Instagram?
 
Currently working with a friend of mine on a 6 slot panel for the middle console. This panel snaps into place like the Oem panel and accepts factory and aftermarket Toyota switches. First print will be done 4/9 and I will test fit and post pics. Here is the rendering for now. It will be printed in black petg with a textured finish on the front flat. Will more than likely be selling these for about $55 shipped. That may change depending on shipping, but I can't imagine much. I will keep this thread updated for reference to the panel from other forums.

***UPDATE*** as of 10/30/21 $55
These are in production now. PM me if you want one. Payment through Paypal or Venmo. $55 shipped.
Have had a few people ask about custom switch locations, ie, pressure gauge, temp gauge less switches... Just need the measurements/layout for what you are wanting and can draw it up. Will be $65 for a custom setup though.

***install instructions***
We made the side clips extra "clippy" so they are a very secure fit. Do your best to have everything ready to go before you put it in. It is very difficult to get your fingers under there to push the clips out. I used AOB switches. Use 2005-2007 Tundra center console as the switch type. There was variation on the clip of the switch from one switch to another, about a 1/64 so we took out that 1/64, you may have to sand a little on the back depending on the tolerance of your switch, but I doubt it.

View attachment 2639727

View attachment 2645535

View attachment 2645542

View attachment 2645543

View attachment 2645544
Are these still available? I would like to purchase one?
 
Did a custom for the addition of a volt/usb PD charger. 30mm round hole, $65 shipped
Screenshot 2022-05-16 084651.png
 
I'm interested in one of these. Are you still making them? Or have made one for the overhead section for the sequoia?
 

Users who are viewing this thread

Back
Top Bottom