Miller Spectrum 375 or 375 Extreme?

Degnol · 04-26-08, 04:46 PM

The "Extreme" weighs less but has some kinda neat qualities. Little more expensive than a 375. Who has either machine? Comments?

THX

Ed

Miller - Plasma Cutters - Spectrum® 375

Miller - Plasma Cutters - Spectrum® 375 X-TREME

Junk · 04-26-08, 06:23 PM

Wrong forum dude

BTW, go with a cutmaster 39 - you'll be much happier

Degnol · 04-26-08, 08:21 PM

Quote:

Originally Posted by Junk

Wrong forum dude

BTW, go with a cutmaster 39 - you'll be much happier

Din' you use to be a MOD? Jebus, suck one cock and they take away MOD status??????

I'll check it out.....TD used to be the one, the only. I think Miller is just copying their sheit.
Do you gots one?

Ed

Junk · 04-27-08, 08:10 AM

Dude I haven't been a mod for like 3 yrs now

. I had a hypertherm 380, a cutmaster 38 and when I was in the consumer test group for Miller had a chance to use the 375. I now have the newer cutmaster 39 and really like it. Just seems like the ratings are more reliable versus what I'd had previously. If I were buying another plasma, I'd only look at Hypertherm or TD, then buy whichever I had better access locally for consumables.

BTW, Hypertherm at least used to, not sure if they still do, have an agreement with Miller. They either made the 375 for Miller or Miller made the 380 for them. Can't remember which way the deal went - but read up a bit on the hobartwelds forum and post this question in the right forum

Degnol · 04-27-08, 11:31 AM

OK, I went to that forum and they seem to like it. One guy could not cut O2 bottles and was pissed

But everyone else who commented seemed to like it. They are about a hundy less than the Miller Spectrum 375 and they are still blue, like my miller stuff (VERY IMPORTANT

)
I'm sold.....

Ed

White Shark · 04-27-08, 11:50 AM

Thermal Dynamics. The best you can find out there IMHO. Cookiemonster and I did a ton of research before throwing down some coin. Love it.

Thermal Dynamics - Home

They produce the Cutmaster as Junk mentioned. As usual, he is correct.

...

04-26-08, 04:46 PM	#1
Degnol Noaccount Webwheeler Join Date: Jan 2003 Location: Kansastitty TLCA# 14529 Posts: 6,467	Miller Spectrum 375 or 375 Extreme? The "Extreme" weighs less but has some kinda neat qualities. Little more expensive than a 375. Who has either machine? Comments? THX Ed Miller - Plasma Cutters - Spectrum® 375 Miller - Plasma Cutters - Spectrum® 375 X-TREME __________________ There is nothing so depraved as a man in the depths of an ether binge '66FJ40, Fresh 2F, H42/Orion(By Poser...LCR4WD), ARB Front/rear(By Poser...LCR4WD), MetalTech Cage installed by Poser, Screw-ups fixed(by Poser) 4WDB Corvette Master, Mini Truck PS, 3.5" Lift, Warn 8274, 33s on stockers

04-27-08, 11:31 AM	#5
Degnol Noaccount Webwheeler Join Date: Jan 2003 Location: Kansastitty TLCA# 14529 Posts: 6,467	OK, I went to that forum and they seem to like it. One guy could not cut O2 bottles and was pissed But everyone else who commented seemed to like it. They are about a hundy less than the Miller Spectrum 375 and they are still blue, like my miller stuff (VERY IMPORTANT) I'm sold..... Ed __________________ There is nothing so depraved as a man in the depths of an ether binge '66FJ40, Fresh 2F, H42/Orion(By Poser...LCR4WD), ARB Front/rear(By Poser...LCR4WD), MetalTech Cage installed by Poser, Screw-ups fixed(by Poser) 4WDB Corvette Master, Mini Truck PS, 3.5" Lift, Warn 8274, 33s on stockers

04-27-08, 11:50 AM	#6
White Shark IH8MUD Addict Join Date: Dec 2004 Location: Red Triangle TLCA# I can't remember... Posts: 670	Thermal Dynamics. The best you can find out there IMHO. Cookiemonster and I did a ton of research before throwing down some coin. Love it. Thermal Dynamics - Home They produce the Cutmaster as Junk mentioned. As usual, he is correct. ... __________________ . ,,____________,, ./ ./,=========" ---------------> <")))>-< /_/ . `·.. ><((((º>`·. .· `·. .· `·... ><((((º> Speargun Power! *Bene legere saecla vincere.*

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

04-26-08, 06:23 PM	#2
Junk IH8MUD Lifer Join Date: Dec 2002 Location: buggerville nj Posts: 5,886 Blog Entries: 1	Wrong forum dude BTW, go with a cutmaster 39 - you'll be much happier

04-27-08, 08:10 AM	#4
Junk IH8MUD Lifer Join Date: Dec 2002 Location: buggerville nj Posts: 5,886 Blog Entries: 1	Dude I haven't been a mod for like 3 yrs now . I had a hypertherm 380, a cutmaster 38 and when I was in the consumer test group for Miller had a chance to use the 375. I now have the newer cutmaster 39 and really like it. Just seems like the ratings are more reliable versus what I'd had previously. If I were buying another plasma, I'd only look at Hypertherm or TD, then buy whichever I had better access locally for consumables. BTW, Hypertherm at least used to, not sure if they still do, have an agreement with Miller. They either made the 375 for Miller or Miller made the 380 for them. Can't remember which way the deal went - but read up a bit on the hobartwelds forum and post this question in the right forum