factory alarm on 1997 80? (1 Viewer)

[jacksobase]

How do you know if you have a factory of aftermarket alarm. 1997 80 no key fob (no remote) small red button to left of side mirror controls > I need to remove or disengage alarm but not sure if factory of aftermarket. Does this sound like a factory alarm or what else can i look for to indicate if alarm is oem.

thx

Jacksonbase

 

[JCruse]

My 97 has a small red light there with a bezel that says CLIFFORD on it and there's a small rocker switch next to it. The PO (second owner) said it wasn't connected. I don't know if this is a dealer install or aftermarket. I also didn't get a fob.

 

[western flyer]

My 80 came from the east coast (port of entry) and it came with a port-installed Audiovox alarm. It has the little red LED near the mirror controls.

 

[livinoffroad]

I read here somewhere that, there is no such thing as a "factory" alarm. they all arrived without a security system and, depending on which port your vehicle arrived, determined which security system was installed.
My vehicle was delivered to San Pedro, CA, and a "TVSS" or Toyota Vehicle Security System was installed at that point. This system appears to be the most "factory" looking, as it says "Toyota" on it, and is serviced thru Toyota dealers. In the manual, it says, "congratulations on the ADDITION of a Toyota Security system to your vehicle".
Perhaps this system was installed on several different Toyota vehicles.
Go to this thread https://forum.ih8mud.com/80-series-tech/582228-cant-program-replacement-remote-97-lx450.html , and you should find the complete owners manual I scanned in for reference.
Perhaps Cdan, or other Toyota gurus could chime in about the "factory" aspect, just for clarification.

 

[western flyer]

^^^^^ This.

 

[TicoCafe]

Ok...I have a 1997 CE. Car came with 1 key FOB which was in bad shape... Bought a new FOB today at the dealer. Came to the site to learn how to program the new remote.

Looked under the Driver seat and Nothing...looked behind the Glove box and Nothing...went behind the drivers side kick panel and below is a pick of what I found. Its an alarm box with a part # 00014-S0200 . Search the site with no availability...went to the interweb and got some hits on how to program with the Valet Light Button (see pic below).

Here are the detailed instructions...I got mine programmed with no issues. Hope this will help the community


Here you go. Hope this helps.
--------------------------------------------
PROGRAMMING ADDITIONAL or REPLACEMENT TRANSMITTERS


Each SECURIKEY+ system can be operated by up to four (4) different
SECURIKEY+ transmitters. The system is supplied from the factory with two
(2) transmitters included, and additional transmitters are available through
parts distribution. Any new or replacement transmitters will need to be
programmed to the main control module before they will activate the system.
The SECURIKEY+ main control module uses a six (6) channel radio frequency
receiver; each channel controlling a different function of the SECURIKEY+
system. Each transmitter button can be programmed to only one of the
receiver channels (e.g., the GREEN button cannot be programmed to operate
the headlight feature and remote start option; it can operate only one or
the other feature). The following is a list of each receiver channel, and
the function of each channel.


CHANNEL # FEATURE CONTROLLED BY THIS CHANNEL
1 Lock
2 Unlock
3 Trunk Release (optional kit required; not available on all models)
4 30 second headlight activation (only if required by GREEN button)
5 Remote panic (only if required by GREEN button instead of LOCK
button)
6 Remote start (optional kit required; not available on all models)


To program new or additional transmitters, or when adding options to
existing SECURIKEY+ transmitters, follow the step by step programming
instructions found below. When programming, it is important to complete each
step of the procedure within 15 seconds, or the system will terminate the
programming mode. If this happens, simply start again.


Be sure that the SECURIKEY+ system is disarmed, and the lighted valet switch
is in the off (out) position before you begin.
Turn the vehicle's ignition key to the on position.
Press then release the L.E.D. valet switch 6 times.
CHANNEL 1: LOCK & Panic Feature Horn Chirps 1 Time L.E.D. Flashes 1 Time
To program the LOCK button on the transmitter, press and hold the LOCK
button until the vehicle's horn sounds one loud chirp. Repeat this for all
transmitters that need the LOCK button programmed (up to four transmitters).
After the LOCK button on all transmitters have been programmed, press and
release the L.E.D. valet switch 2 times to advance to the next receiver
channel.


CHANNEL 2: UNLOCK Feature Horn Chirps 2 Times L.E.D. Flashes 2 Times
To program the UNLOCK button on the transmitter, press and hold the UNLOCK
button until the vehicle's horn sounds one loud chirp. Repeat this for all
transmitters that need the UNLOCK button programmed (up to four
transmitters).
After the UNLOCK button on all transmitters have been programmed, press and
release the L.E.D. valet switch 2 times to advance to the next receiver
channel.


CHANNEL 3: TRUNK RELEASE Option Horn Chirps 3 Times L.E.D. Flashes 3
Times
To program the TRUNK RELEASE option on the transmitter, press and hold the
GREEN option button until the vehicle's horn sounds one loud chirp. Repeat
this for all transmitters that need the GREEN option button programmed (up
to four transmitters).
After the TRUNK RELEASE button on all transmitters have been programmed,
press and release the L.E.D. valet switch 2 times to advance to the next
receiver channel.


CHANNEL 4: 30 SECOND HEADLIGHT Feature Horn Chirps 4 Times L.E.D.
Flashes 4 Times
To program the HEADLIGHT option on the transmitter, press and hold the GREEN
option button until the vehicle's horn sounds one loud chirp. Repeat this
for all transmitters that need the GREEN option button programmed (up to
four transmitters).
After the HEADLIGHT button on all transmitters have been programmed, press
and release the L.E.D. valet switch 2 times to advance to the next receiver
channel.


CHANNEL 5: Separate PANIC Button Feature Horn Chirps 5 Times L.E.D.
Flashes 5 Times
To program the PANIC option on the transmitter, press and hold the GREEN
option button until the vehicle's horn sounds one loud chirp. Repeat this
for all transmitters that need the GREEN option button programmed (up to
four transmitters).
After the PANIC button on all transmitters have been programmed, press and
release the L.E.D. valet switch 2 times to advance to the next receiver
channel.


CHANNEL 6: REMOTE START Feature Horn Chirps 6 Times L.E.D. Flashes 6
Times
To program the REMOTE START option on the transmitter, press and hold the
GREEN option button until the vehicle's horn sounds one loud chirp. Repeat
this for all transmitters that need the GREEN option button programmed (up
to four transmitters).
After the REMOTE START button on all transmitters have been programmed,
press and release the L.E.D. valet switch 2 times to advance to terminate
programming mode, or simply turn the ignition key to the off position to
terminate the transmitter programming mode.


PROGRAMMING THE SELECTABLE FEATURES
The SECURIKEY+ system offers a number of selectable features that can be
changed, allowing you to custom fit the system to your customer. The
following is a list of the features that are selectable and can be changed
using the valet switch and any transmitter that is programmed to the system
installed in the vehicle.


FEATURE # FUNCTION 1 CHIRP 2 CHIRPS
1 Headlights on for 20 seconds during disarm ON or OFF
2 Headlights on for 20 seconds during arm ON or OFF
3 Automatic ignition controlled door lock ON or OFF
4 Automatic ignition controlled door unlock ON or OFF
5 Auto unlock driver's door only or all doors Driver's door or
All doors
6 Active or Passive arming Passive or Active
7 Active or Passive door locks Passive or Active
8 Trunk release output - 1 second or latched 1 second or
Latched
9 Panic on lock button or option button Option or Lock
10 Trunk Release Hold - 1 second or 2 presses Hold 1 Sec or
2 Times


To change the selection of any of these features, follow the step by step
programming procedures, and do not allow more then 15 seconds to pass
between any two steps or the system will terminate the programming mode.
There is no need to complete the entire programming sequence. After the
appropriate features have been changed, simply turn the ignition key off to
terminate the programming mode.


Be sure that the SECURIKEY+ system is disarmed, and the lighted valet switch
is in the off (out) position before you begin.
Turn the vehicle's ignition key to the on position.
Press then release the L.E.D. valet switch 6 times.
Immediately turn the ignition key off then back on.


FEATURE 1 LED Flashes 1 Time
1 Chirp = Headlights ON During Disarm Horn Chirps either 1 or 2 Times
2 Chirps = Headlights OFF During Disarm
To change the selection, press and release the lock button on the
transmitter, which will be indicated by the appropriate 1 or 2 chirp signal
from the horn. If you do not want to change this feature, simply press and
release the L.E.D. valet switch 2 times to advance to programmable feature
number 2.


FEATURE 2 LED Flashes 2 Times
1 Chirp = Headlights ON During Arm Horn Chirps either 1 or 2 Times
2 Chirps = Headlights OFF During Arm
To change the selection, press and release the lock button on the
transmitter, which will be indicated by the appropriate 1 or 2 chirp signal
from the horn. If you do not want to change this feature, simply press and
release the L.E.D. valet switch 2 times to advance to programmable feature
number 3.


FEATURE 3 LED Flashes 3 Times
1 Chirp = Ignition controlled door locks ON Horn Chirps either 1 or 2
Times
2 Chirps = Ignition controlled door locks OFF
To change the selection, press and release the lock button on the
transmitter, which will be indicated by the appropriate 1 or 2 chirp signal
from the horn. If you do not want to change this feature, simply press and
release the L.E.D. valet switch 2 times to advance to programmable feature
number 4.


FEATURE 4 LED Flashes 4 Times
1 Chirp = Ignition controlled unlock ON Horn Chirps either 1 or 2 Times
2 Chirps = Ignition controlled unlock OFF
To change the selection, press the lock button on the transmitter, which
will be indicated by the appropriate 1 or 2 chirp signal from the horn. If
you do not want to change this feature, simply press and release the L.E.D.
valet switch 2 times to advance to programmable feature number 5.


FEATURE 5 LED Flashes 5 Times
1 Chirp = Ignition controlled unlock DRIVER'S DOOR Horn Chirps either 1
or 2 Times
2 Chirps = Ignition controlled unlock ALL DOORS
To change the selection, press the lock button on the transmitter, which
will be indicated by the appropriate 1 or 2 chirp signal from the horn. If
you do not want to change this feature, simply press and release the L.E.D.
valet switch 2 times to advance to programmable feature number 6.


FEATURE 6 LED Flashes 6 Times
1 Chirp = PASSIVE ARMING (Automatic Arming) Horn Chirps either 1 or 2
Times
2 Chirps = ACTIVE ARMING (Arm by Remote Only)
To change the selection, press the lock button on the transmitter, which
will be indicated by the appropriate 1 or 2 chirp signal from the horn. If
you do not want to change this feature, simply press and release the L.E.D.
valet switch 2 times to advance to programmable feature number 7.


FEATURE 7 LED Flashes 7 Times
1 Chirp = PASSIVE DOOR LOCKS Horn Chirps either 1 or 2 Times
2 Chirps = ACTIVE DOOR LOCKS
To change the selection, press the lock button on the transmitter, which
will be indicated by the appropriate 1 or 2 chirp signal from the horn. If
you do not want to change this feature, simply press and release the L.E.D.
valet switch 2 times to advance to programmable feature number 8.


FEATURE 8 Do not change this feature selection. It should be left in the
factory preset (1 chirp) mode. Press and release the L.E.D. valet switch 2
times to advance to programmable feature 9.


FEATURE 9 LED Flashes 9 Times
1 Chirp = Remote Panic / GREEN transmitter button Horn Chirps either 1 or
2 Times
2 Chirps = Remote Panic / LOCK transmitter button
To change the selection, press the lock button on the transmitter, which
will be indicated by the appropriate 1 or 2 chirp signal from the horn. If
you do not want to change this feature, simply press and release the L.E.D.
valet switch 2 times to advance to programmable feature number 10.


FEATURE 10 LED Flashes 10 Times
1 Chirp = Trunk Release HOLD GREEN BUTTON 1 SECOND Horn Chirps either 1
or 2 Times
2 Chirps = Trunk Release PRESS GREEN BUTTON 2 TIMES
To change the selection, press the lock button on the transmitter, which
will be indicated by the appropriate 1 or 2 chirp signal from the horn. If
you do not want to change this feature, simply press and release the L.E.D.
valet switch 2 times to exit the programming mode.

 

[BTUMAN]

I have the same alarm on my 97 CE and it was unplugged when I received it with only one remote. I found the actual programming instruction manual that may help. See link below.

http://jjguy.com/securikey/securikeycommonmanual.pdf

Followed these and I had it going in 5 min.

 

[97LandCruser]

TicoCafe

where did you get the key for the remote. is it something that could be purchased separately? i want to have the key in the remote. i can dremel it to fit. but i would rather buy one. thanks
i would like to possibly get a remote start module to work with that alarm.

 

[DARKNESS]

If the alarm is basically useless then it's the factory system.

 

[Mr Cimarron]

I removed the "brain" from mine but then ended up with manual door locks. I'm living with it at the moment till I make time to reconnect the door power wire that was cut to go through the brain. Manual locks are much better than a crappy key fob and annoying alarm sounds when reconnecting the battery.

 

[98 SNAKE EATER]

If the alarm is basically useless then it's the factory system.

Mine is factory, but far from useless

 

[Hornd]

Tear the factory alarm out and have a Viper put in (industry Leader/Standard).
Bought a 5104 on Ebay for $100 and had installed for $90.
Got alarm, remote door lock/unlock and car starter. Works further away then I could yell.
The factory system is 90s tech, or about as useful as the tape deck.
If you don't have the money, then save your extra $ from gassing up at $2 instead of $4 and apply that.

 

[DARKNESS]

Mine is factory, but far from useless

What exactly is that?

 

[98 SNAKE EATER]

What exactly is that?

Nathan Airchime K3HA

 

[98 SNAKE EATER]

Stock horn vs K3HA

 

[FJonny81]

Tear the factory alarm out and have a Viper put in (industry Leader/Standard).
Bought a 5104 on Ebay for $100 and had installed for $90.
Got alarm, remote door lock/unlock and car starter. Works further away then I could yell.
The factory system is 90s tech, or about as useful as the tape deck.
If you don't have the money, then save your extra $ from gassing up at $2 instead of $4 and apply that.

Did you have buy harness for the new unit?

 

[Hornd]

No harness needed.

 

[cahill]

...The factory system is 90s tech, or about as useful as the tape deck......

I like the factory tape deck

 

[Nekkit]

Thats what i have. No idea what for is the second button (one is to on/off alarm open/close locks)

 

[Hornd]

I think intent was to program 2 Separate Cars to Single Remote. I never had the bottom button work either.