Search results for query: *

Forum search Google search

  1. DaneDK

    Stock OEM clutch ratings

    Does anyone know the ratings of a stock OEM clutch for the 1hdft? My 80 was optimized by a dyna test and torque is now 511 Nm at 1775 rpm. BUT I have been doing a bit of light towing, and the clutch is now slipping in 4th around peak torque. It as a genuine Toyota clutch with max 20K on it (4...
  2. DaneDK

    Steering wheel clunk

    There is a clunking sound from my steering wheel when rotating lightly from side to side. The sound is only there on the rotational direction, not when pulling steering wheel in/out. There sems to be play somewhere at the top of the steering column/steering wheel - It is not in the rubber joint...
  3. DaneDK

    Weird e-brake?

    After doing rotors, pads and brake shoes, the e-brake on passenger side is acting up: It binds up much sooner in the reverse direction than the forward direction when adjusting the cog wheel at the rotor. Also in general, it does seem more "sticky" on the forward direction compared to drivers...
  4. DaneDK

    Rear brake caliper slide pin boot?

    Will have a go at it... Thanks :)
  5. DaneDK

    Rear brake caliper slide pin boot?

    I need to replace the slide pin boots on my rear calipers. The bottom hole is a "normal" type boot that attaches to the opening of the pin bolt hole in the caliper. But the top hole is a different kind, that goes through all the way through the hole, illustrated in the attached (47769-22010). I...
  6. DaneDK

    Iron man ext brackets sbext005

    Just fitted ironman sbext005 swaybar ext kit, but it seems that the holes through which the rod/hanger which connects to the stabilizer bar, are not alumnes/centered the Stock brackets. Does this look right? Seems that SBEXT005 previous was the bracket kit I have mounted, but According to...
  7. DaneDK

    1HD-FT timing belt replacement interval

    Probably why the 1HD-FTE has a 150K timing belt service interval with it's electronically controlled injection timing I guess.
  8. DaneDK

    1HD-FT timing belt replacement interval

    Thanks for the replies. I appreciate it. I saw this "hint" in the FSM too but was not sure if this in fact is the specified service interval for my region - but you are probably right that it is the same for all regions then. Also normally the manafacturers would specify for example 100.000 km...
  9. DaneDK

    1HD-FT timing belt replacement interval

    I have been trying to find out which replacement intervals apply for the timing belt of a 1HD-FT (24-valve). Apparently it is not stated in the FSM, or at least I cannot find it. From what I understand, the replacement intervals can differ from region to region, so I am after the European data...
  10. DaneDK

    HDJ80 belt screeching

    The 2 new belts have been tightened and re-tightened. Using a crowbar against alternator and engine as the factory adjustment screw and bracket tend to bend. I dont think it should be tightened further. I know that they are supposed to be very tight - there is a lot of pull on these two rather...
  11. DaneDK

    HDJ80 belt screeching

    On my 1HD-FT the alternator/water pump belts keep squealing once and a while. I have replaced them with new Continental from same production batch - In other words they are not paired from Toyota, but are of the same production lot at Continental. The belts are tightened quite according to...
  12. DaneDK

    105 series side steps on 80 series LC

    Thanks for the info. I am currently waiting for a reply from iron man regarding differences between their 80 series and 105 series item numbers. Maybe some minor things like brake line spacers etc.
  13. DaneDK

    105 series side steps on 80 series LC

    I am trying to find out, if a set of Iron Man side steps for the LC105 series will fit on a 80-series. The chassis should be identical, but I was thinking that maybe body mounts etc. have been moved on the 105 series, to accommodate the 105 body? The sidesteps are the bolt-to-chassis kind, not...
  14. DaneDK

    Should the air filter drain hole be sealed?

    Right, thanks... :-)
  15. DaneDK

    Should the air filter drain hole be sealed?

    OK, thanks, will have a look at the so called "tuna can" :-)
  16. DaneDK

    Should the air filter drain hole be sealed?

    1HDFT: I read different opinions on whether or not the drain hole in the air filter housing should be sealed - when having a snorkel fitted for the occasional deep river crossing. There is a bit of moisture entering the snorkel head which of course needs to get out, and therefore a 100% sealing...
  17. DaneDK

    Help. Broken bolt - 80-series running boards

    You are right, I would like to mount the running boards again after I have been driving without them for a while. Turns out my sills and bottom half of doors cannot live without them. There are literally hundreds of chips to the bare metal due to stone debris being thrown up the the MT's. 3...
  18. DaneDK

    Help. Broken bolt - 80-series running boards

    I am looking for a way to extract a bolt that has broken on my 80-sereis. The running boards on the 80-series are held by 4 brackets which bolt into the body. Each bracket is bolted in with 2 bolts (top and bottom). It is the rear most bracket and then the bolt at top which has snapped - It is...
  19. DaneDK

    DC DS with drop arms, still vibrations... what to do next?

    Right, thanks scrowley, will have a look at lokka.com.
  20. DaneDK

    DC DS with drop arms, still vibrations... what to do next?

    From the Marks 4WD Adaptors fittings instructions it doesn't look complicated. Do I need to buy any replacement gaskets or is it all liquid gasket?
Back
Top Bottom