100 Series Slee Skid Plates - SOLD!
Selling 100 series slee skid plate system.
Brand new never installed.
No hardware.
Prefer local sale but will ship at your cost.
Large Main Plate $375
Front Plate $275
Center (Intermediate) Plate $160
Will sell as a complete set or...
Answers to a PM
TC and BB just extra, I worked @ a Lexus dealer and they were replaced on customer vehicles for very minor issues and I snagged them before they were thrown away. Neither replaced on this truck.
PS not out just sluggish.
1998 100 Series, 181,000 miles !!!SOLD!!!
!!!!!!!SOLD!!!!!!!
After much debating with myself, I have decided to part with my 100 series. It has been my wife's daily driver for the last 2 years and she wants something else. I can't justify keeping it since it hasn't been wheeling in over a...
There is a TSB for this problem. PM me your e-mail and I can send you the pdf.
It is a problem in the lh fuse block (aka j/b) down by the dead pedal. I have fixed many without changing the j/b. The TSB also has you remove about 8 wires from various connectors (redundant grounds that are...
There are two ears on the back of the plastic splash shield. Usually just trim them off where the leave the main part of the splash shield. Sorry no pics, tore mino off long ago. I think part of it is in Ouray somewhere.
Sorry, I was kind of unclear in the description. I should read before i post. Anyway, the most likely damage that could've occured (glad everything turned out alright by the way) is the valves could've become bent from piston contact due to the belt being off more than a few teeth. Bent...
You'll/They'll know when they get it back on right (if its the t-belt) because if any internal damage was done it will have misfire codes. Even if they are that is about all the damage that it will cause, if it did at all. I might recommend to the svc mgr if it goes that far you maybe want one...
Here is a link with some early prototype pics and one post beating pic - https://forum.ih8mud.com/100-series-cruisers/154256-skid-plate-crossmember.html
And these are Slee's I'm just a product tester.:cool:
I can't seem to find any of the other pics of the times during CM07 the belly pan...
Basically the two fattest shims that will go in without excessive force, preload will usually increase about 5-10 in/lbs above factory spec. (Pinion preload + Side bearing preload). Only side preload will change.
No 2/3, if you can get it started and completely seated and have to work to...
Seen them fail both ways (spiders and ring/pinion) not with the arb though. Ring gear failure is usually because under load the gear deflects and then all of your setup measurements are shot and the rest is history.
Highly recommend when putting the new one together you add to the side...
Nice writeup & Nice truck, I like it when all the electrical stuff works and is functional.
X10 on the DVD! But I won't let em watch it while we are wheeling, too much other good stuff to see.
Sorry guys, been really busy for the last few months. New job and all.
Anyway be patient they are very close to done (all 3) and you will all know when they are available.
:D
And sorry fish, santa will have to get you something else.
Quick rundown,
p0300 - less than 18% misfire
all individual cyl codes 18-50%, 50 is dead miss.
best advice, need to hook up toyota scan tool (unfortunately)
it will tell you the misfire percentage on each cyl. Higher percentage is most likely the problem. I would bet you either have a...
140a fuse is bolted in. Should be able to pop the clear cover off and visually inspect it. Only time it blows is if the car is jumped backwards:eek:
b+ terminal on alt - the one bolted on with a 10mm bolt, and the plastic connector on the back which should have three wires in it.