Search results for query: *

Forum search Google search

  1. S

    Rear bump stop spacers 80 series 2.0''/2 1/2''

    would you ship to Brisbane Australia
  2. S

    Auto oil pan gasket question

    Thanks, I will get some as a backup plan cheers
  3. S

    Auto oil pan gasket question

    Hi All I am about to replace the auto oil filter and one thing I noticed is my kit came with a gasket, looks part rubber part cork. I had a look at the current oil pan and I don't seem to notice a gasket like this. From the service manual it states you should use the below Apply seal packing...
  4. S

    LCA or UCA

    Have read a lot about upper and lower control Arms that are slightly longer then stock. Which is the best one to go with to adjust the diff angle after a lift the lower or upper arms. Cheers J Sent from my iPhone using IH8MUD
  5. S

    CEL code 52 after fuel filter change

    Just to let you know I finally solved this riddle. The wire was exposed as in insulation in the wire was cracked. From what I have learned about knock sensors is the ECM expects a certain voltage signal from the knock sensor and with the insulation exposing the wire, the voltage signal from...
  6. S

    how many miles do you have on your 80

    1994, got 287000 km, oil change every 5000. Still sorting out issues:-). It seems that comes with territory with an high mileage cruiser. Sent from my iPhone using IH8MUD
  7. S

    New guy looking at an 80 tomorrow..

    Have a look at this below site if you are buying a cruiser it tells you the basic things to look for. I still got mine looked at by a outfit that do all the standard tests like oil pressure, coolant pressure. Compression test and then some. At least you know what you are in for as well as it...
  8. S

    Help need with no oil pressure

    Just to close this thread off, the oil pressure sender takes two wire connectors a white one which slides into a male connection on the side on and a black connector that slides in on the top of the sender. My issue is the black connection and come off and the sliding on and off was very loose...
  9. S

    Rough Idle

    Any update on your fix Sent from my iPhone using IH8MUD
  10. S

    Rough Idle

    Check your leads and spark plugs. 30 to 60 minute job. Check that the plugs are not fouled and look in good nick. Also check the gap in the plugs. Also maybe a good idea to inspect the dissy and rotor condition and lead to the coil. These are all quick and easy checks. Pull your PVC value and...
  11. S

    Help need with no oil pressure

    Thanks for the info just for clarity the sender should take two plugs and white one and a black one. Cheers J Sent from my iPhone using IH8MUD
  12. S

    Help need with no oil pressure

    Anyone willing to offer any advice ? Sent from my iPhone using IH8MUD
  13. S

    Help need with no oil pressure

    Sent from my iPhone using IH8MUD
  14. S

    Help need with no oil pressure

    My dash gauge is dead and would like to know how to test and where to look for issues. History below 1994 FZJ80 auto Australian model Just done and oil and filter change Also change fuel filter and air filter I also have a CEL code 52 at the moment as well, which I think is the front knock...
  15. S

    CEL code 52 after fuel filter change

    Bump Sent from my iPhone using IH8MUD
  16. S

    CEL code 52 after fuel filter change

    Hi all I got the CEL code 52 ( knock sensor 1 ) after changing the fuel filter. Has Anyone had this issue before. I might have broken something while doing the FF. I will do a continuity test tonight as per FSM is there anything else I should look at like the connectors, is there a test for...
  17. S

    Noise on Decel Help

    2x on what Dave said Sent from my iPhone using IH8MUD
  18. S

    Noise on Decel Help

    You could also pull your rear DS and lock centre diff (if you have CDL switch) and see if the noise disappears or quietens down or if it is still noisy at least you can exclude a few things Sent from my iPhone using IH8MUD
  19. S

    Noise on Decel Help

    Could be rear pinion bearing , had mine replaced and now noise is gone. Also check rear wheel bearings Sent from my iPhone using IH8MUD
  20. S

    The infamous check engine light

    With older 80's which don't have the standard code diag you will need to use a piece of metal wire like a paper clip and connect the T1 and E1 connectors in the diag box wich should be against your firewall. Just do a search in mud for it and there are a few writeups showing how to pull the...
Back
Top Bottom