i have replaced my compressor, dryer, and expansion valve i'll be charging at work but i have no clue how much oil to put in it?
also has anyone tryed the sp oil instead of the d? type oil
the ac guy at work says it's better but i'm sceptical
thanks for the site and the writeup on the...
with the engine running pull 1 wire off the cap and see if it stumbles, if it does put 1 back on and do the same with 2, 3,4,5,6
if you find one that doesn't make it stumble when you pull it off bingo theres your cylinder issue
to narrow it down even further you can swap plugs with another...
if you trim the bottom of the shroud, the efficiency of the fan is lessened and it seems we need all we can get with these cruisers.
i would either drill holes to lower or make some brackets.
alkaline747trio i live denver, nc if your over this way i have a shop with plenty of tools if you...
do you have a fsm
you might see if there is a way the test the tps (throttle posistion sensor)
i had this problem on a tpi chevy that drove me nuts
same conditions you mention
heck i don't even know if your motor has one but if it does do a voltage test with the multimeter
hope it helps if...
just got through putting in the sears die hard platinum group 31 battery
i did cut a little out of the bottom right corner off the tray for it to fit
there was some wires routed there so i cut a piece of heater hose to protect it
i cut my factory hold down strap and widened it 5/8 inch...
does anyone have a good source to buy the sst
the local stealership wouldn't sell me one and told me to try snapon
i made a butch one to get the job done but i would rather have the correct tool
this happened to me about two weeks after i got mine
the culprit is probably the heater core under the seat
yank the seat and heater ducting and take the fan assembly
apart and remove all the gum m/m's wrappers pretzels and the like and look for a bunch of green goo on the copper core...
i'm kinda in the same situation
but i need to keep mine low enough for my wife and baby cus they use it every day and we use it for camping regularly
my plan used omes when i hit the right deal until then
either buy the 30mm spacers for the front only
armor front sides & rear
but i'm...
sorry didn't mean to jump on you i didn't mean it that way
i just was hoping everyone on here didn't go out to there garage and cut up there arms cus everyone on here has or will have caster issues.
I KNOW YOU DID IT RIGHT I WAS A WELDER BY TRADE AND NOW DO BOTH TECH AND WELDER ON HEAVY...
sorry i wouldn't trust welding cast to any monkey with a mig gun!:rolleyes:
i just don't want my arms falling apart while i drive down the road with my wife and child with me
now that you've posted those pics you need to get off the net now and put them suckers on and in about an hour you may get back on and post up the other pics!!!!
let me quess merry christmas?
in any case enjoy!!:D
how soon are you planning on getting the combo i kinda have a hookup and if we buy together we might be able to work some more with the price?
options, options ,options.........:crybaby:
where are you at i work in charlotte and live in maiden
since i'm from your area and most of these guys aren't you forgot to mention we do not have mud in nc remember
WE HAVE GREASY CLAY THAT LOOKS LIKE MUD
i've wheeled with about anything and everything out here and lockers do help but in our type of "mud" lockers don't mean squat
i've got...
if you had the hoses and clamps it wouldn't be even a comparison to the phh
i had to remove because mine leaked on me getting the carpet also
i say if your going to go through all that trouble to go that far apart take that sucker loose and flush the thing out with the garden hose and get...
what is the price ?
could never find anything out very concrete
why does this have to be installed there
i work on turbo diesels all day long and put on custom turbo kit's on chevy,dodge,ford you name it on the side all the time?? do you think if i talked to them they would let meinstall ...
http://www.ottindustries.com/fj80.htm
they make these for people that put fj80 front axles in toy trucks cus they run leaf springs and also need the tie rod and relay rod in front so it doesn't interfere with there oil pan placement!!
hope this helps!!
enjoy ryan
it can also be an extra cab
that's what i got mine from
and remember it's the rear shaft not the front
i'm pretty sure it needs to be a 4x4 or a prerunner package
the 2wd surly sits to low to need that kind of shaft
not sure on the others
hope this helps
ryan:D
i've noticed a slight coolent smell coming from the middle of the cruiser for about a week and today i checked the coolent and it was about 1/2 gallon low
so i filled it up with antifreeze and went to the store to stock up on some pm stuff
when i got home i pulled in the shop and jacked...