19101-61240 CAP ASSY
90916-03052 THERMOSTAT
19102-43060 ROTOR
I get good rates. I guess not worht it to ship to far.
I live in Richmond hill and work in west Toronto for local guys
you could use racking(pallet racking)8<> 10ft high (uprights) x 4 and 6 to 8 cross beams 8 feet or 10 feet or 12 feet depending how wide you have. build 2 sets of pallet racking then tarp or use old 4x8.
I have lots around,I don't want to spend $200-500 if I have material here.
I estimate cost...
I can see this a possibility but 2 starters :(
Try turning the motor by hand like grabbing the belts and such.
If you cannot turn it put a socket and bar on the crank them try to turn.
I tried pushing while in 1rst gear,couldn t budge,will try pulling with chain tonite.
So if...
all ground cables where replaced(if corroded) and all ground bolts taken off cleaned off rust and put back on.
35inchoverdrive Check the connections on your ground strap(block/starter to frame.) yup that one was bad changed
I tried a boosting as well. while on the on the truck just...
So here is the story
replaced a lot of the grounds and various wires that where hard or corroded.
Ever since my starter dosen't turn,when installed. It just plunges "click"
I have pulled it and tested it on a battery,clicks and spins
I have pulled the clip connection and ran a wire to...
I ll try this in the AM :bang: 3 hrs from now
Godwin et3Surge, I'd replace both the contacts and the plunger as this repair is easy and cheap. If this takes care of your starter problems then you're in good shape. But even if you have more severe starter problems and need to use your starter...
oil inside engine, actually dipstick was pretty good,but PO could of changed it a month earlier
Didn't boil over No
I changed(garage) when I got certification done. Along with ALL fluids besides :o rad.
I ll double verfy if THEY did the job,paid cash to save 15% rear,transfer...
running RICK it was. Carb ,air intake... everything THE smell from the exhaust
Compression
1 @125
2 @ 130
I stop compression testing. Get depressed quick
no matter,LC ran b4,senses got invovled oil,gaz,green or yellow red but it RAN
Really needed canisters to dump the...
environment + procedure
good one
do not have that tool NEED it :)
PRIOR to starting this project:
`search...read
` located some canisters. To bleed/clean the fj60(lot's of liters/gallons of pollute)
read /searched
was going to do a lt1 swap but found 85 bj60
anyone interested in a complete z28 car lt1
car spun out @ 80 kmh and hit gardrail,passenger side damage front+ rear
looking for $2k
can cut ship front clip only
located in Tronto Ontario Canada
CAN and WILL ship worldwide
marc@alllaser.ca
There s also brown(oil)
could it just be that it ran real rich or am i looking @ another pricier issue.
Should I flush and see what happens,drive around with water for a bit?
thanks
MA
oops I forgot,also have a 57 chev P/U it s gona be satin 500%
the cruiser will be durabak black or gray or orange,used to walk by a benz that was durabak'd black and loved the look.
got a local guy in Scaboro to do body kit and paint my 90 Celica GTS
Satin Black aka flat black
some peeps like it ,I loved it,called it the shadow,did the rims also,looked SICK.
Was thinking of doing the cruiser also satin also.
The issue I found(maybe wasn't sealed proper) scratches IE...
YUP TINKER,THAT MAKES SENSE caps off sorry
I was and hoping for answer before going home.
Anyways,I bought a roll of 12-14-16,should cover most.
I just can t believe the PO or PO's hacking,there are more wires hanging around then being used.
I will be re wiring everything I can over...
as stated in a prior post
Took it over to mechanics last week to get a safety.
On my way there (about 20km HWY a wire from the ignition coil to carb shorted the engine,my bro was following,sait there was a 2 foot flame out of exhaust.
Mechanic says he changed wires,(all taped up).
I took a...