Search results for query: *

Forum search Google search

  1. landtank

    Orange Fan Clutch install.

    I’ve been seeing high torque wedge belts for our 80s for a while. Good insurance agains slipping under heavy loads
  2. landtank

    LANDTANK - SUPERCHARGER

    that's something I can push through if there is interest in it.
  3. landtank

    LANDTANK - SUPERCHARGER

    no, they just built what I designed
  4. landtank

    LANDTANK - SUPERCHARGER

    You could wrap the unit but the water flow is such that it exits over the exhaust manifold on its way back to the radiator.
  5. landtank

    LANDTANK - SUPERCHARGER

    yes
  6. landtank

    LANDTANK - SUPERCHARGER

    Back from MOAB and got some testing done and wanted to share some stuff. First, I know this is taking some time but I'm engineering a lot of stuff and doing so simultaneously so while it looks like I'm jumping around it's all intended to dovetail together in the end. Today's update is the...
  7. landtank

    Factory rear E locker FZJ

    You need to notch the open diff slightly on one side. No big deal.
  8. landtank

    Wit's End Turbo Owners - Thread #2.....

    My custom bell intercooler was $1000.00 , two years ago for a 1 off. Just for reference
  9. landtank

    How fked am I?

    It’s a radiator inside a cavity of coolant. There are gaskets and I think I’ve seen 1 pic of a hole in the radiator. You have to take it out and inspect it. Typical HG is coolant in your oil. You seem to have oil in your coolant. Drain down you coolant and pull off the oil cooler cover...
  10. landtank

    How fked am I?

    don't overlook the possibility of an oil cooler issue.
  11. landtank

    Wit's End Turbo Owners - Thread #2.....

    I ended up with a custom bell-intercooler setup for my Super Charger. they're more efficient than the Chinese ones which allows for a smaller package. But the throttle body is mounted on the chargers intake so there is a lot more room up top.. From memory it's a 3.7" thick unit.
  12. landtank

    Seat position

    With my kit the seat still bolts to the floor in the same position. What I did was modify the rail so it operates in the same range but 2” back. No loss of head room.
  13. landtank

    Help diagnosing front end clunk

    Do you have 555 brand TREs? They can rust and get noisy.
  14. landtank

    Seat position

    I’m 6’6” with a 36” inseam. My seat brackets were design 1 right after the purchase. I’ve owned multiple 80s who all got the kit. I find that the amount of increase is fine. Cloth seats fall short of the modified electric seats by about a half inch in travel.
  15. landtank

    Help diagnosing front end clunk

    Check your nuts. On the right knuckle
  16. landtank

    Alignment and Steering Wheel Question

    Installing caster correction will take a lot of that out.
  17. landtank

    Solving parasitic draw

    My understanding of zener diodes is they only pass a certain voltage. In this case it might be 12v. Since a charged battery is usually around 12.3v and has a charging voltage or 14.2v. Passing only 12v would ensure that the rings brightness is constant. But I could be wrong.
  18. landtank

    Replacing fuel tank filler neck

    I put a new pipe in whole with the body on. I compressed the pipe from being round to an oval. Then jacked up on the rear floor for extra room and forced the pipe in. Then using a c-clamp round out the pipe again. The pipe interfaces with a rubber connector so being perfectly round isn’t a...
  19. landtank

    1FZ Denso fuel injector depinning advice?

    On old connectors like that I take a pair of channel locks and adjust them so the jaws are parallel when clamped on h to he housing snd then crack the housing like you would walnuts.
  20. landtank

    White smoke fuel smell after Bosch injector upgrade. Help?

    the bosch injectors use wiring adapters. You said you didn't use them.
Back
Top Bottom