LANDTANK performance MAF housing

rlabair · 02-20-09, 09:33 PM

I rechecked the wires, all good. i cleared the cel and it came on immediately again. I took it apart, cleaned the Maf sensor again and reinstalled it, cel still on so I cleared it again, cel appeared again with same code. I emailed the person I bought the sensor from and he is sending a 22204-07010 to replace it. I'll keep ya posted. Thanks all!

arndog123 · 02-21-09, 05:22 PM

I paypal'ed ya on the 9th and still haven't got it yet. Can you please give me a status? Thanks.

Arnold

landtank · 02-22-09, 10:16 AM

Quote:

Originally Posted by arndog123

I paypal'ed ya on the 9th and still haven't got it yet. Can you please give me a status? Thanks.

Arnold

I checked my records and tracked it through USPS and it shows being delivered on 2/20/09. It's a priority flat rate box.

rlabair · 02-23-09, 09:35 PM

Update on my install. Just rec'd my replacement sensor, installed it with no CEL! Easy overall install, noticeable improvement to highway mileage on first tank of gas as well as smoother idle and improved response. Very nicely done! Thanks again

arndog123 · 02-24-09, 12:44 AM

Quote:

Originally Posted by landtank

I checked my records and tracked it through USPS and it shows being delivered on 2/20/09. It's a priority flat rate box.

Got it. My parents did not see it because the mailman hid it behind a big plant at their front door.

landtank · 02-24-09, 05:44 AM

glad you both are all set.

tucsonlx · 02-24-09, 07:51 PM

Any Left, everyone is recommending them for towing and I think I will need all the help I can get.

locrwln1 · 02-26-09, 07:45 AM

Paypal and PM sent.

Looking forward to this.

Jack

Edit: Got in on Saturday the 28th. Great looking product, can't wait to install it.

ply426 · 03-03-09, 10:34 PM

Still have any left ???

landtank · 03-04-09, 03:12 AM

I have 4 of them

alexdell · 03-08-09, 12:00 PM

I finally installed the housing yesterday. I bought a used sensor for $32 on ebay. I have not monitored the gas mileage yet but it definitely has a quicker response.

Thanks Rick.

Alex

33tab · 03-08-09, 04:08 PM

Quote:

Originally Posted by landtank

I've actually have 15 units in house and am not sure If I'll reorder. Not trying to push you just being up front.

Sorry this is my first post and I'm not sure if I'm doing it right. Am I reading this correctly in assuming that you are not going to make any more? I have a '97 LX-450 with the TRD supercharger and I'm trying to weight all of the mods that I need before I commit. I know that there is more information in the research thread but I haven't had time to read it. If these are the last ones I don't want to miss out though.

landtank · 03-08-09, 08:22 PM

I currently have two housings. I agreed to hold one of them for a short time to give that member a chance to pay.

Right now I'm undecided on whether or not I'll make more.

landtank · 03-08-09, 08:55 PM

the only one left is on hold, I'll post back either way after the 14th.

solidfrontaxle · 03-08-09, 11:53 PM

You BETTER make more! I need one of these so bad!

Solid Taco · 03-09-09, 02:21 AM

Yeah! Make more! I need one too. Just got me an lx and I want to do these mod too.

uabericm · 03-09-09, 07:34 AM

Hopefully you will make more...I now have the funds and they are gone.

hzavarce · 03-10-09, 07:38 PM

I want one too. Let us know when you are going to make more.

Thanks !

Biaggi · 03-13-09, 08:01 AM

Quote:

Originally Posted by landtank

the only one left is on hold, I'll post back either way after the 14th.

Sorry fellas, I got the last one

UPDATE 3/25/09:
I just installed the Landtank's MAF and a used sensor I bought from Ebay seller (riceburner91)
for $29 +S/H ( he has several). Instructions were straight forward! I was so eager to put it on that it was a bit drizzling outside and I didn't care and was trying to get the pin wires relocated. After really looking into that dirty plug harness, it was a snap to switch it out ;-)

The only issue I had was the removal of the harness from the stock sensor. I thought it was a flat screwdriver pry-up tab and I accidentally cracked the tab but ended up just taking the screw driver and edge it back from the oem MAF sensor.
So no harm done....

After I reinstalled it and put the end caps on the vacuum lines, I crossed my fingers and and hoped it would idle fine once I crank it up. So I cleared all the existing CEL by after unhooking the battery for a few minutes and reconnected it. I then started LEXI up and it idled a bit high to get warmed up and once it got under 1k RPM I went for a spin. Since this isn't my daily driver I couldn't tell a major diff, but I have a full tank of gas and will compare my mpg and how it performs while towing my popup.
I'm psyched!!!! Thanks LANDTANK!!!

Thanks again Rick!

JMZ- · 03-17-09, 06:18 PM

Am I too late? I want one too! Let us know if you'll make more. Thanks.

lndcruz · 03-20-09, 09:38 PM

bump for if your going to make more, Might be interested.

solidfrontaxle · 03-20-09, 09:45 PM

I AM interested. I have money in hand, and will send it to you now just so you can get some more made.

hzavarce · 03-21-09, 09:29 AM

I'll send money too !!!

landtank · 03-30-09, 04:21 PM

I've had a lot of interest in having another batch made. It would be 4-6 weeks out before delivery. I'd like to guage the interest before I commit to the order. If you are still interested please send me a PM and whether or not you would be will to pre pay. With enough interest the price would remain at $205.00 + $15.00 S&H

Thanks

solidfrontaxle · 03-30-09, 07:57 PM

Whew! You don't know how happy this makes me! I was thinking about it today just hoping that you would make another batch. PM Sent!

JMZ- · 03-31-09, 12:25 AM

whew! I'm thinking about it everyday! PM sent.

landtank · 04-10-09, 12:44 PM

The order has been put on hold for now as I'm investigating a sensor change.

jeremy000 · 04-22-09, 11:32 AM

Any update?

I'm interested in your next batch.

landtank · 04-22-09, 05:22 PM

too much drama from one individual. Sorry, but I don't need that in my life. There have been a couple ones in the for sale section. If it comes with a sensor be sure to clean it well. If you are not sure how PM me and I can help out.

solidfrontaxle · 04-22-09, 06:06 PM

Sad!

So are you done? Is the entire project over? Are you going to improve on it?