plugs, wires, cap, rotor, seals DONE!!

98 SNAKE EATER · 06-27-08, 09:31 PM

Well, I had a set of plugs, wires, cap and rotor sitting in my office for weeks and when I finally got around to doing them on Wednesday, I noticed the #1 oil seal had a slight leak

No point in halfassing it, so I ordered up a set as well as a new valve cover gasket from the local dealer and while they were trucking it over, I decided to grind the hell out of the cover and shoot some lefover Pontiac engine blue

(the only high temp paint I had on hand)

Also shot the top covers in bed liner for a gritty look

Under the cover, there was a little varnish (I only run dino oil), but nuthin out of the ordinary

The old wires showed some signs of arcing and the old plugs (NGK's) had a bit of carbon, but were dry as a bone (I'll get some pix of those tomorrow)

concretejungle · 06-27-08, 09:39 PM

wow, interesting color.

Chevinater77 · 06-28-08, 12:51 PM

i like your N-EVERSTART

98 SNAKE EATER · 06-28-08, 03:49 PM

Fixed that problem yesterday

06-27-08, 09:39 PM	#2
concretejungle IH8MUD Tour Guide Join Date: Oct 2003 Location: North Cadillac TLCA# 14646 Posts: 5,912	wow, interesting color. __________________ 95' FZJ80 OME med./J lift, ARB rack, ARB Bull Bar w/tmax 12,500, 315 Nitto, stainless brake lines, Center Diff Lock, Sliders, IPOR Skid, IPOR rear bumper, upgraded slee sticker, custom dents, more to come. . . Remember it's a gateway drug, so it will actually lead to "crystal meh".

06-28-08, 12:51 PM	#3
Chevinater77 IH8MUD Regular Join Date: Feb 2007 Location: Wenatchee, Washington Posts: 228	i like your N-EVERSTART __________________ Its not a Passion, its an Obsession Cruiser~95 stock 80 series, Goodyear Forterra Triple-Treds, Samco sport PHH. Princess Ride~2008 Toyota Tundra Crewmax limited Chevinater~ 77 Chevy 3/4 ton 350/350/203 with 44 front 14ff rear, 4.56s, 6 inchs 35x12.5x16.5 bfg m/t

06-28-08, 03:49 PM	#4
98 SNAKE EATER IH8MUD Addict Join Date: Aug 2004 Location: Queens, NYC and sometimes Orlando, FL Posts: 972	Fixed that problem yesterday __________________ 98 Aztek T/A WS7 (FOR SALE!!) 70 Ram Air IV T/A 97 FZJ80 Locked 00 Lifted G16E GhettoChopper 07 Ghetto Quad (FOR SALE!!)

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

06-27-08, 09:31 PM	#1
98 SNAKE EATER IH8MUD Addict Join Date: Aug 2004 Location: Queens, NYC and sometimes Orlando, FL Posts: 972	plugs, wires, cap, rotor, seals DONE!! Well, I had a set of plugs, wires, cap and rotor sitting in my office for weeks and when I finally got around to doing them on Wednesday, I noticed the #1 oil seal had a slight leak No point in halfassing it, so I ordered up a set as well as a new valve cover gasket from the local dealer and while they were trucking it over, I decided to grind the hell out of the cover and shoot some lefover Pontiac engine blue (the only high temp paint I had on hand) Also shot the top covers in bed liner for a gritty look Under the cover, there was a little varnish (I only run dino oil), but nuthin out of the ordinary The old wires showed some signs of arcing and the old plugs (NGK's) had a bit of carbon, but were dry as a bone (I'll get some pix of those tomorrow) __________________ 98 Aztek T/A WS7 (FOR SALE!!) 70 Ram Air IV T/A 97 FZJ80 Locked 00 Lifted G16E GhettoChopper 07 Ghetto Quad (FOR SALE!!)